[      0.000][3-1][      0][  0][IMP-info]systick init success
[      0.000][3-1][      0][  0][IMP-info]timer init success
[      0.000][3-1][      0][  0][IMP-info]watchdog inited success
[      0.000][3-1][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.000][3-1][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.010][3-1][      0][  0][IMP-info]imp chip 3 die 1 mac 0 card 0x0 ncl init success
[      0.010][3-1][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.010][3-1][      0][  0][IMP-info]mdio init success
[      0.010][3-1][      0][  0][IMP-info]sgpio init entry
[      0.055][3-1][      0][  0][IMP-info]bios setup init success.
[      0.055][3-1][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.110][3-1][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.120][3-1][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.120][3-1][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.220][3-1][      0][  0][IMP-info]mac 0 phy init config 0
[      0.220][3-1][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.220][3-1][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.220][3-1][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.220][3-1][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.325][3-1][      0][  0][IMP-info]mac 1 phy init config 0
[      0.325][3-1][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.325][3-1][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.325][3-1][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.325][3-1][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.425][3-1][      0][  0][IMP-info]mac 2 phy init config 0
[      0.425][3-1][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.425][3-1][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.425][3-1][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.425][3-1][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.530][3-1][      0][  0][IMP-info]mac 3 phy init config 0
[      0.530][3-1][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.530][3-1][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.530][3-1][      0][  0][IMP-info]init intr aging 0
[      0.530][3-1][      0][  0][IMP-info]TM not bypass
[      0.530][3-1][      0][  0][IMP-info]not support l2 forward
[      0.530][3-1][      0][  0][IMP-info]flow director init mode 0
[      0.530][3-1][      0][  0][IMP-info]nic init success
[      0.530][3-1][      0][  0][IMP-info]rocee init success
[      0.530][3-1][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.530][3-1][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.530][3-1][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.530][3-1][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.530][3-1][      0][  0][IMP-info]imp version is 30a1703 
[      0.530][3-1][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.530][3-1][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.530][3-1][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.530][3-1][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     46.340][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     46.340][3-1][      0][  0][IMP-info]mac 0 link driver port type 3
[     46.340][3-1][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     46.355][3-1][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     46.375][3-1][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     46.375][3-1][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     46.445][3-1][      0][  0][IMP-info]mac 0 phy usage change to 1
[     46.445][3-1][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     46.445][3-1][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     46.445][3-1][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     46.540][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     46.540][3-1][      0][  0][IMP-info]mac 1 link driver port type 3
[     46.540][3-1][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     46.570][3-1][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     46.595][3-1][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     46.595][3-1][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     46.640][3-1][      0][  0][IMP-info]mac 1 phy usage change to 1
[     46.640][3-1][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     46.645][3-1][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     46.645][3-1][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     46.745][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     46.745][3-1][      0][  0][IMP-info]mac 2 link driver port type 3
[     46.745][3-1][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     46.755][3-1][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     46.790][3-1][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     46.790][3-1][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     46.845][3-1][      0][  0][IMP-info]mac 2 phy usage change to 1
[     46.845][3-1][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     46.845][3-1][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     46.845][3-1][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     46.940][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     46.940][3-1][      0][  0][IMP-info]mac 3 link driver port type 3
[     46.940][3-1][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     46.955][3-1][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     46.975][3-1][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     46.975][3-1][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     47.045][3-1][      0][  0][IMP-info]mac 3 phy usage change to 1
[     47.045][3-1][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     47.045][3-1][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     47.045][3-1][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     48.590][3-1][      0][  0][IMP-info]mac 0 update phy speed 3 duplex 1
[     48.590][3-1][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 0 tx 0
[     80.275][3-1][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     80.290][3-1][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     80.310][3-1][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     80.325][3-1][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     80.340][3-1][      0][  0][IMP-info]imp_global_reset_handle start
[     80.350][3-1][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     80.350][3-1][      0][  0][IMP-info]mac 0 link driver port type 2
[     80.350][3-1][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     80.350][3-1][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     80.350][3-1][      0][  0][IMP-info]mac 1 link driver port type 2
[     80.350][3-1][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     80.350][3-1][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     80.350][3-1][      0][  0][IMP-info]mac 2 link driver port type 2
[     80.350][3-1][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     80.350][3-1][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[     80.350][3-1][      0][  0][IMP-info]mac 3 link driver port type 2
[     80.350][3-1][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[     80.355][3-1][      0][  0][IMP-info]init intr aging 0
[     80.355][3-1][      0][  0][IMP-info]TM not bypass
[     80.355][3-1][      0][  0][IMP-info]not support l2 forward
[     80.355][3-1][      0][  0][IMP-info]flow director init mode 0
[     80.355][3-1][      0][  0][IMP-info]nic init success
[     80.355][3-1][      0][  0][IMP-info]rocee init success
[     80.355][3-1][      0][  0][IMP-info]imp_global_reset_handle end
[     80.355][3-1][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     80.355][3-1][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     80.355][3-1][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     80.355][3-1][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     81.125][3-1][      0][  0][IMP-info]imp starts to enter the OS state
[    184.490][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    184.495][3-1][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    184.495][3-1][      0][  0][IMP-info]mac 0 link driver port type 3
[    184.495][3-1][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    184.595][3-1][      0][  0][IMP-info]mac 0 phy usage change to 1
[    184.595][3-1][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    184.650][3-1][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    184.650][3-1][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    184.670][3-1][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    184.715][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    184.715][3-1][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    184.715][3-1][      0][  0][IMP-info]mac 1 link driver port type 3
[    184.715][3-1][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    184.720][3-1][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    184.815][3-1][      0][  0][IMP-info]mac 1 phy usage change to 1
[    184.815][3-1][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    184.815][3-1][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    184.840][3-1][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    184.880][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    184.885][3-1][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    184.885][3-1][      0][  0][IMP-info]mac 2 link driver port type 3
[    184.885][3-1][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    184.890][3-1][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    184.985][3-1][      0][  0][IMP-info]mac 2 phy usage change to 1
[    184.985][3-1][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    184.985][3-1][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    185.005][3-1][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    185.050][3-1][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    185.050][3-1][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    185.050][3-1][      0][  0][IMP-info]mac 3 link driver port type 3
[    185.050][3-1][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    185.055][3-1][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    185.155][3-1][      0][  0][IMP-info]mac 3 phy usage change to 1
[    185.155][3-1][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    185.155][3-1][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    185.175][3-1][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    203.290][3-1][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    203.295][3-1][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    203.295][3-1][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    203.300][3-1][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    205.395][3-1][      0][  0][IMP-info]mac 0 update phy speed 3 duplex 1
[    205.395][3-1][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 0 tx 0
[    205.915][3-1][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
