[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.000][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.005][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]mdio init success
[      0.005][0-0][      0][  0][IMP-info]sgpio init entry
[      0.050][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.100][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.110][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.110][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.520][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.520][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.520][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.520][0-0][      0][  0][IMP-info]init intr aging 0
[      0.520][0-0][      0][  0][IMP-info]TM not bypass
[      0.520][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a1703 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     37.315][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     37.315][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     37.315][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     37.325][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     37.345][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     37.345][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     37.415][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     37.415][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     37.415][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     37.415][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     37.505][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     37.505][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     37.505][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     37.515][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     37.535][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     37.535][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     37.605][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     37.605][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     37.605][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     37.605][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     37.690][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     37.690][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     37.690][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     37.710][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     37.730][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     37.730][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     37.790][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     37.790][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     37.790][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     37.790][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     37.890][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     37.890][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     37.890][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     37.900][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     37.920][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     37.920][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     37.990][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     37.990][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     37.990][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     37.990][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     39.245][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     39.245][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     73.155][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     73.175][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     73.190][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     73.205][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     73.225][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[     73.235][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     73.235][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[     73.235][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     73.235][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     73.235][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[     73.235][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     73.235][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     73.235][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[     73.235][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     73.235][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[     73.235][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[     73.235][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[     73.235][0-0][      0][  0][IMP-info]init intr aging 0
[     73.235][0-0][      0][  0][IMP-info]TM not bypass
[     73.235][0-0][      0][  0][IMP-info]not support l2 forward
[     73.235][0-0][      0][  0][IMP-info]flow director init mode 0
[     73.235][0-0][      0][  0][IMP-info]nic init success
[     73.235][0-0][      0][  0][IMP-info]rocee init success
[     73.235][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[     73.235][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     73.235][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     73.235][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     73.235][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     74.230][0-0][      0][  0][IMP-info]imp starts to enter the OS state
[    101.685][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    101.685][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    101.685][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    101.685][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    101.690][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    101.690][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    101.785][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    101.785][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    101.785][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    101.810][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    101.855][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    101.860][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    101.860][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    101.860][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    101.860][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    101.860][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    101.960][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    101.960][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    101.960][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    101.980][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    102.030][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    102.030][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    102.030][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    102.030][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    102.030][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    102.030][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    102.130][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    102.130][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    102.130][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    102.140][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    102.185][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    102.185][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    102.185][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    102.185][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    102.190][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    102.190][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    102.290][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    102.290][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    102.290][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    102.305][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    115.270][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    115.270][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    115.275][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    115.275][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    118.560][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    118.560][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    119.080][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.000][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.005][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]mdio init success
[      0.005][0-0][      0][  0][IMP-info]sgpio init entry
[      0.050][0-0][      0][  0][IMP-info]bios setup init success.
[      0.050][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.100][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.110][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.110][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.210][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.210][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.210][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.210][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.210][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.415][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.415][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.415][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.415][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.415][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.515][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.515][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.515][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.520][0-0][      0][  0][IMP-info]init intr aging 0
[      0.520][0-0][      0][  0][IMP-info]TM not bypass
[      0.520][0-0][      0][  0][IMP-info]not support l2 forward
[      0.520][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.520][0-0][      0][  0][IMP-info]nic init success
[      0.520][0-0][      0][  0][IMP-info]rocee init success
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.520][0-0][      0][  0][IMP-info]imp version is 30a1703 
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     39.050][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     39.050][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     39.050][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     39.060][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     39.080][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     39.080][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     39.150][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     39.150][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     39.150][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     39.150][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     39.230][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     39.230][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     39.230][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     39.255][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     39.270][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     39.270][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     39.330][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     39.330][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     39.335][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     39.335][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     39.425][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     39.425][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     39.425][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     39.440][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     39.455][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     39.455][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     39.530][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     39.530][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     39.530][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     39.530][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     39.635][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     39.635][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     39.635][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     39.645][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     39.665][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     39.665][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     39.735][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     39.735][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     39.735][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     39.735][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     40.995][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     40.995][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     75.275][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     75.290][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     75.310][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     75.325][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     75.340][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[     75.350][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     75.350][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[     75.350][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     75.350][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     75.350][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[     75.350][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     75.350][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     75.350][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[     75.350][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     75.350][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[     75.350][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[     75.350][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[     75.355][0-0][      0][  0][IMP-info]init intr aging 0
[     75.355][0-0][      0][  0][IMP-info]TM not bypass
[     75.355][0-0][      0][  0][IMP-info]not support l2 forward
[     75.355][0-0][      0][  0][IMP-info]flow director init mode 0
[     75.355][0-0][      0][  0][IMP-info]nic init success
[     75.355][0-0][      0][  0][IMP-info]rocee init success
[     75.355][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[     75.355][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xe, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     75.355][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     75.355][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     75.355][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     75.355][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     76.150][0-0][      0][  0][IMP-info]imp starts to enter the OS state
[    103.850][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    103.850][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    103.850][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    103.850][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    103.855][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    103.855][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    103.955][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    103.955][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    103.955][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    103.970][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    104.010][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    104.015][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    104.015][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    104.015][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    104.015][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    104.015][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    104.115][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    104.115][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    104.115][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    104.115][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    104.160][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    104.160][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    104.160][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    104.160][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    104.165][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    104.165][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    104.265][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    104.265][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    104.265][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    104.265][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    104.310][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    104.310][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    104.310][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    104.310][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    104.310][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    104.310][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    104.410][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    104.410][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    104.410][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    104.435][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    118.555][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    118.560][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    118.560][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    118.565][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    121.725][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    121.725][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    122.245][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.000][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.005][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]mdio init success
[      0.005][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.060][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.320][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.320][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.320][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.320][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.320][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.525][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.525][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.525][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a1703 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     76.540][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     76.540][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     76.540][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     76.550][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     76.570][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     76.570][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     76.640][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     76.640][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     76.640][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     76.640][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     76.725][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     76.725][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     76.725][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     76.740][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     76.755][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     76.755][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     76.825][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     76.825][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     76.825][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     76.830][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     76.935][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     76.935][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     76.935][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     76.945][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     76.965][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     76.965][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     77.035][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     77.035][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     77.035][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     77.035][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     77.130][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     77.130][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     77.130][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     77.140][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     77.160][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     77.160][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     77.230][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     77.230][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     77.230][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     77.230][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     78.495][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     78.495][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    110.255][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    110.275][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    110.290][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    110.310][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    110.325][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[    110.335][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[    110.335][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[    110.335][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[    110.335][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[    110.335][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[    110.335][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[    110.335][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[    110.335][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[    110.335][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[    110.335][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[    110.335][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[    110.335][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[    110.335][0-0][      0][  0][IMP-info]init intr aging 0
[    110.335][0-0][      0][  0][IMP-info]TM not bypass
[    110.335][0-0][      0][  0][IMP-info]not support l2 forward
[    110.335][0-0][      0][  0][IMP-info]flow director init mode 0
[    110.335][0-0][      0][  0][IMP-info]nic init success
[    110.335][0-0][      0][  0][IMP-info]rocee init success
[    110.335][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[    110.335][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    110.335][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    110.335][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    110.335][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    111.060][0-0][      0][  0][IMP-info]imp starts to enter the OS state
[    139.605][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    139.605][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    139.605][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    139.605][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    139.610][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    139.610][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    139.705][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    139.705][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    139.705][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    139.710][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    139.765][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    139.770][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    139.770][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    139.770][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    139.770][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    139.770][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    139.870][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    139.870][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    139.870][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    139.885][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    139.930][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    139.930][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    139.930][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    139.930][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    139.935][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    139.935][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    140.035][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    140.035][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    140.035][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    140.040][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    140.085][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    140.085][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    140.085][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    140.085][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    140.090][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    140.090][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    140.190][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    140.190][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    140.190][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    140.200][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    153.030][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    153.035][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    153.035][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    153.040][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    156.445][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    156.445][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    156.965][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.000][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.005][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.005][0-0][      0][  0][IMP-info]mdio init success
[      0.005][0-0][      0][  0][IMP-info]sgpio init entry
[      0.050][0-0][      0][  0][IMP-info]bios setup init success.
[      0.050][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.100][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.110][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.110][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.210][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.210][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.210][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.210][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.210][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.415][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.415][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.415][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.415][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.415][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.520][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.520][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.520][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.520][0-0][      0][  0][IMP-info]init intr aging 0
[      0.520][0-0][      0][  0][IMP-info]TM not bypass
[      0.520][0-0][      0][  0][IMP-info]not support l2 forward
[      0.520][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.520][0-0][      0][  0][IMP-info]nic init success
[      0.520][0-0][      0][  0][IMP-info]rocee init success
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.520][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.520][0-0][      0][  0][IMP-info]imp version is 30a1703 
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.520][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    102.975][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[    102.975][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    102.975][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    102.990][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    103.005][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[    103.005][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    103.075][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    103.075][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    103.075][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    103.075][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    103.190][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[    103.190][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    103.190][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    103.205][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    103.220][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[    103.220][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    103.295][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    103.295][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    103.295][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    103.295][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    103.380][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[    103.380][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    103.380][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    103.390][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    103.410][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[    103.410][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    103.480][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    103.480][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    103.480][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    103.480][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    103.590][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[    103.590][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    103.590][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    103.605][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    103.625][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[    103.625][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    103.695][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    103.695][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    103.695][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    103.695][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    105.025][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    105.025][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    134.975][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    134.995][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    135.010][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    135.030][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    135.045][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[    135.055][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[    135.055][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[    135.055][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[    135.055][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[    135.055][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[    135.055][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[    135.055][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[    135.055][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[    135.055][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[    135.055][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[    135.055][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[    135.055][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[    135.055][0-0][      0][  0][IMP-info]init intr aging 0
[    135.055][0-0][      0][  0][IMP-info]TM not bypass
[    135.055][0-0][      0][  0][IMP-info]not support l2 forward
[    135.055][0-0][      0][  0][IMP-info]flow director init mode 0
[    135.055][0-0][      0][  0][IMP-info]nic init success
[    135.055][0-0][      0][  0][IMP-info]rocee init success
[    135.055][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[    135.055][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    135.055][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    135.055][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    135.055][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    135.910][0-0][      0][  0][IMP-info]imp starts to enter the OS state
[    164.470][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    164.470][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    164.470][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    164.470][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    164.475][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    164.475][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    164.575][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    164.575][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    164.575][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    164.575][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    164.620][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    164.620][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    164.620][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    164.620][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    164.625][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    164.625][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    164.720][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    164.720][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    164.725][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    164.725][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    164.765][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    164.770][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    164.770][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    164.770][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    164.770][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    164.770][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    164.870][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    164.870][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    164.870][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    164.890][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    164.930][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    164.930][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    164.930][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    164.930][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    164.935][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    164.935][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    165.035][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    165.035][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    165.035][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    165.055][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    179.735][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    179.735][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    179.740][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    179.740][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    183.000][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    183.000][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    183.515][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.520][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.520][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.520][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    149.095][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[    149.095][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    149.095][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    149.105][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    149.125][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[    149.125][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    149.195][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    149.195][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    149.195][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    149.195][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    149.285][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[    149.285][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    149.285][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    149.300][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    149.315][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[    149.315][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    149.385][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    149.385][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    149.390][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    149.390][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    149.480][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[    149.480][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    149.480][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    149.490][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    149.520][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[    149.520][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    149.580][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    149.580][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    149.580][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    149.580][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    149.680][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[    149.680][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    149.680][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    149.690][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    149.710][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[    149.710][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[    149.780][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    149.780][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    149.780][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    149.780][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    151.075][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    151.075][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    151.595][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[    269.265][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    269.280][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    269.300][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    269.315][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    269.315][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[    269.315][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x1 pma_sig 0x1
[    269.330][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[    269.340][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[    269.340][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[    269.340][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[    269.340][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[    269.340][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[    269.340][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[    269.340][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[    269.340][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[    269.340][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[    269.340][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[    269.340][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[    269.340][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[    269.345][0-0][      0][  0][IMP-info]init intr aging 0
[    269.345][0-0][      0][  0][IMP-info]TM not bypass
[    269.345][0-0][      0][  0][IMP-info]not support l2 forward
[    269.345][0-0][      0][  0][IMP-info]flow director init mode 0
[    269.345][0-0][      0][  0][IMP-info]nic init success
[    269.345][0-0][      0][  0][IMP-info]rocee init success
[    269.345][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[    269.345][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    269.345][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    269.345][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    269.345][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    298.640][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    298.640][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    298.640][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    298.640][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    298.645][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    298.645][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    298.740][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    298.740][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    298.740][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    298.755][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    298.800][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    298.800][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    298.800][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    298.800][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    298.805][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    298.805][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    298.905][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    298.905][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    298.905][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    298.925][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    298.975][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    298.975][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    298.975][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    298.975][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    298.975][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    298.980][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    299.075][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    299.075][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    299.075][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    299.095][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    299.140][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    299.140][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    299.140][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    299.140][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    299.145][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    299.145][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    299.245][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    299.245][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    299.245][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    299.260][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    313.065][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    313.065][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    313.070][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    313.070][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    316.355][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    316.355][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    316.875][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.320][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.320][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.320][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.320][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.320][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.525][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.525][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.525][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     42.110][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     42.110][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     42.110][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     42.125][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.140][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     42.140][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.215][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     42.215][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     42.215][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     42.215][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     42.290][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     42.290][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     42.290][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     42.305][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.320][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     42.320][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.390][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     42.390][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     42.390][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     42.390][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     42.475][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     42.475][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     42.475][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     42.500][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.515][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     42.515][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.575][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     42.575][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     42.575][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     42.575][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     42.675][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     42.675][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     42.675][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     42.700][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.720][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     42.720][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.780][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     42.780][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     42.780][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     42.780][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     44.030][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     44.030][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     44.550][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[    796.135][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    796.155][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    796.170][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    796.185][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    796.185][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[    796.185][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x1 pma_sig 0x1
[    796.205][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[    796.215][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[    796.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[    796.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[    796.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[    796.215][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[    796.215][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[    796.215][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[    796.215][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[    796.215][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[    796.215][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[    796.215][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[    796.215][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[    796.215][0-0][      0][  0][IMP-info]init intr aging 0
[    796.215][0-0][      0][  0][IMP-info]TM not bypass
[    796.215][0-0][      0][  0][IMP-info]not support l2 forward
[    796.215][0-0][      0][  0][IMP-info]flow director init mode 0
[    796.215][0-0][      0][  0][IMP-info]nic init success
[    796.215][0-0][      0][  0][IMP-info]rocee init success
[    796.215][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[    796.215][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    796.215][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    796.215][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    796.215][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    825.505][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    825.505][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    825.505][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    825.505][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    825.510][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    825.510][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    825.610][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    825.610][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    825.610][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    825.625][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    825.670][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    825.675][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    825.675][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    825.675][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    825.675][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    825.675][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    825.775][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    825.775][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    825.775][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    825.795][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    825.845][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    825.845][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    825.845][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    825.845][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    825.850][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    825.850][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    825.945][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    825.945][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    825.945][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    825.970][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    826.030][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    826.030][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    826.030][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    826.030][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    826.035][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    826.035][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    826.135][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    826.135][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    826.135][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    826.135][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    839.585][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    839.590][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    839.590][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    839.595][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    842.820][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    842.820][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    843.340][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[ 596697.880][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[ 596697.880][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x0 pma_sig 0x1
[ 596703.410][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[ 596703.410][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[ 596703.935][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.020][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.020][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.020][0-0][      0][  0][IMP-info]mdio init success
[      0.020][0-0][      0][  0][IMP-info]sgpio init entry
[      0.065][0-0][      0][  0][IMP-info]bios setup init success.
[      0.070][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.115][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.125][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.125][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.230][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.230][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.230][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.230][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.230][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.330][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.330][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.330][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.330][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.330][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.435][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.435][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.435][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.435][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.435][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.535][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.535][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.535][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.535][0-0][      0][  0][IMP-info]init intr aging 0
[      0.535][0-0][      0][  0][IMP-info]TM not bypass
[      0.535][0-0][      0][  0][IMP-info]not support l2 forward
[      0.540][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.540][0-0][      0][  0][IMP-info]nic init success
[      0.540][0-0][      0][  0][IMP-info]rocee init success
[      0.540][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.540][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.540][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.540][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.540][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.540][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.540][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.540][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.540][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     49.735][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     49.735][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     49.735][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     49.750][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     49.765][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     49.765][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     49.840][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     49.840][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     49.840][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     49.840][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     49.920][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     49.920][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     49.920][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     49.930][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     49.950][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     49.950][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     50.020][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     50.020][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     50.020][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     50.020][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     50.105][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     50.105][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     50.105][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     50.120][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     50.135][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     50.135][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     50.205][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     50.205][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     50.205][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     50.210][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     50.310][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     50.310][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     50.315][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     50.325][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     50.355][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     50.355][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     50.415][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     50.415][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     50.415][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     50.415][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     51.690][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     51.690][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     52.215][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[     80.690][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     80.705][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     80.725][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     80.740][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     80.740][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[     80.740][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x1 pma_sig 0x1
[     80.755][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[     80.765][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     80.765][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[     80.765][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     80.765][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     80.765][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[     80.765][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     80.765][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     80.765][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[     80.765][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     80.770][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[     80.770][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[     80.770][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[     80.770][0-0][      0][  0][IMP-info]init intr aging 0
[     80.770][0-0][      0][  0][IMP-info]TM not bypass
[     80.770][0-0][      0][  0][IMP-info]not support l2 forward
[     80.770][0-0][      0][  0][IMP-info]flow director init mode 0
[     80.770][0-0][      0][  0][IMP-info]nic init success
[     80.770][0-0][      0][  0][IMP-info]rocee init success
[     80.770][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[     80.770][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     80.770][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     80.770][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     80.770][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    109.925][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    109.930][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    109.930][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    109.930][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    109.935][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    109.935][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    110.030][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    110.030][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    110.030][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    110.050][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    110.100][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    110.100][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    110.100][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    110.100][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    110.100][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    110.100][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    110.200][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    110.200][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    110.200][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    110.200][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    110.245][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    110.245][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    110.245][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    110.245][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    110.250][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    110.250][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    110.350][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    110.350][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    110.350][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    110.365][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    110.410][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    110.410][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    110.410][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    110.410][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    110.415][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    110.415][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    110.510][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    110.510][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    110.515][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    110.530][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    124.865][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    124.865][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    124.870][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    124.870][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    128.100][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    128.100][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    128.620][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.320][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.320][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.320][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.320][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.320][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.525][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.525][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.525][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     42.805][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     42.805][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     42.805][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     42.815][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.835][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     42.835][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.905][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     42.905][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     42.905][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     42.905][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     42.995][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     42.995][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     42.995][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     43.005][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     43.025][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     43.025][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     43.095][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     43.095][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     43.095][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     43.095][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     43.175][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     43.175][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     43.175][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     43.190][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     43.210][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     43.210][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     43.280][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     43.280][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     43.280][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     43.280][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     43.360][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     43.360][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     43.360][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     43.370][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     43.400][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     43.400][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     43.460][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     43.460][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     43.460][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     43.460][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     44.785][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     44.785][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     45.315][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.520][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.520][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.520][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     42.030][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     42.030][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     42.030][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     42.045][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.060][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     42.065][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.135][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     42.135][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     42.135][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     42.135][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     42.220][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     42.220][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     42.220][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     42.230][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.250][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     42.250][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.320][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     42.320][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     42.320][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     42.320][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     42.405][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     42.405][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     42.405][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     42.415][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.445][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     42.445][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.505][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     42.505][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     42.505][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     42.505][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     42.605][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     42.605][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     42.605][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     42.620][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     42.635][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     42.635][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     42.710][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     42.710][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     42.710][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     42.710][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     43.935][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     43.935][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     44.455][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.005][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.520][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.520][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.520][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     38.755][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     38.755][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     38.755][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     38.770][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     38.785][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     38.785][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     38.860][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     38.860][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     38.860][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     38.860][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     38.935][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     38.935][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     38.935][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     38.950][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     38.965][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     38.970][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     39.040][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     39.040][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     39.040][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     39.040][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     39.120][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     39.120][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     39.120][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     39.130][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     39.150][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     39.150][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     39.220][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     39.220][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     39.220][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     39.220][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     39.300][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     39.300][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     39.300][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     39.320][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     39.340][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     39.340][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     39.400][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     39.400][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     39.400][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     39.400][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     40.705][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     40.705][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     41.225][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[     77.055][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     77.070][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     77.090][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     77.105][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     77.105][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[     77.105][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x1 pma_sig 0x1
[     77.120][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[     77.130][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     77.130][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[     77.130][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     77.130][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     77.130][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[     77.135][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     77.135][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     77.135][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[     77.135][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     77.135][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[     77.135][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[     77.135][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[     77.135][0-0][      0][  0][IMP-info]init intr aging 0
[     77.135][0-0][      0][  0][IMP-info]TM not bypass
[     77.135][0-0][      0][  0][IMP-info]not support l2 forward
[     77.135][0-0][      0][  0][IMP-info]flow director init mode 0
[     77.135][0-0][      0][  0][IMP-info]nic init success
[     77.135][0-0][      0][  0][IMP-info]rocee init success
[     77.135][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[     77.135][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     77.135][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     77.135][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     77.135][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    105.600][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    105.600][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    105.600][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    105.600][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    105.605][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    105.605][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    105.700][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    105.700][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    105.705][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    105.725][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    105.770][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    105.770][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    105.770][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    105.770][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    105.775][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    105.775][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    105.875][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    105.875][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    105.875][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    105.895][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    105.945][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    105.945][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    105.945][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    105.945][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    105.945][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    105.945][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    106.045][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    106.045][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    106.045][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    106.060][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    106.105][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    106.105][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    106.105][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    106.105][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    106.105][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    106.105][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    106.205][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    106.205][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    106.205][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    106.225][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    118.540][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    118.545][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    118.545][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    118.550][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    121.845][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    121.845][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    122.365][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.320][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.320][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.320][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.320][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.320][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.525][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.525][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.525][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     26.585][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     26.585][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     26.585][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     26.600][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.620][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     26.620][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.690][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     26.690][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     26.690][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     26.690][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     26.765][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     26.765][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     26.765][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     26.780][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.800][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     26.800][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.870][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     26.870][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     26.870][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     26.870][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     26.960][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     26.960][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     26.960][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     26.975][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.990][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     26.990][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     27.060][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     27.060][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     27.060][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     27.060][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     27.145][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     27.145][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     27.145][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     27.155][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     27.175][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     27.175][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     27.245][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     27.245][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     27.245][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     27.245][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     28.505][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     28.505][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     29.030][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.320][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.320][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.320][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.320][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.320][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.525][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.525][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.525][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     26.500][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     26.500][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     26.500][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     26.510][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.530][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     26.530][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.600][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     26.600][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     26.600][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     26.600][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     26.685][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     26.685][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     26.685][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     26.700][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.720][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     26.720][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.790][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     26.790][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     26.790][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     26.790][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     26.870][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     26.870][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     26.870][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     26.885][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.900][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     26.900][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.975][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     26.975][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     26.975][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     26.975][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     27.050][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     27.050][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     27.050][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     27.075][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     27.095][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     27.095][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     27.155][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     27.155][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     27.155][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     27.155][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     28.420][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     28.420][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     28.940][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.520][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.520][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.520][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     34.750][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     34.750][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     34.750][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     34.765][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     34.780][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     34.780][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     34.850][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     34.850][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     34.850][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     34.850][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     34.930][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     34.930][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     34.930][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     34.940][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     34.960][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     34.960][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.030][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     35.030][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     35.030][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     35.030][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     35.205][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     35.205][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     35.205][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     35.215][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     35.240][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     35.240][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.305][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     35.305][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     35.305][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     35.305][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     35.395][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     35.395][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     35.395][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     35.410][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     35.430][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     35.430][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.500][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     35.500][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     35.500][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     35.500][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     36.775][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     36.775][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     37.300][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[     71.960][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     71.975][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     71.995][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     72.010][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     72.010][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[     72.010][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x1 pma_sig 0x1
[     72.030][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[     72.040][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     72.040][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[     72.040][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     72.040][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     72.040][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[     72.040][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     72.040][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     72.040][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[     72.040][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     72.040][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[     72.040][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[     72.040][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[     72.040][0-0][      0][  0][IMP-info]init intr aging 0
[     72.040][0-0][      0][  0][IMP-info]TM not bypass
[     72.040][0-0][      0][  0][IMP-info]not support l2 forward
[     72.040][0-0][      0][  0][IMP-info]flow director init mode 0
[     72.040][0-0][      0][  0][IMP-info]nic init success
[     72.040][0-0][      0][  0][IMP-info]rocee init success
[     72.040][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[     72.040][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     72.040][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     72.040][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     72.040][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[    100.445][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3f
[    100.450][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 1
[    100.450][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[    100.450][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[    100.455][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    100.455][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[    100.550][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[    100.550][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[    100.550][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    100.570][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[    100.615][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3f
[    100.620][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 1
[    100.620][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[    100.620][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[    100.620][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    100.620][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[    100.720][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[    100.720][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[    100.720][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    100.740][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[    100.790][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3f
[    100.790][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 1
[    100.790][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[    100.790][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[    100.795][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    100.795][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[    100.890][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[    100.890][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[    100.890][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    100.905][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[    100.955][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3f
[    100.955][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 1
[    100.955][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[    100.955][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[    100.955][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    100.960][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[    101.055][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[    101.055][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[    101.055][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[    101.060][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[    113.855][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    113.860][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    113.860][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    113.865][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    117.050][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[    117.050][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[    117.565][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.320][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.320][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.320][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.320][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.320][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.525][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.525][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.525][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     26.475][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     26.475][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     26.475][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     26.485][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.505][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     26.505][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.575][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     26.575][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     26.575][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     26.575][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     26.660][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     26.660][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     26.660][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     26.670][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.690][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     26.690][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.760][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     26.760][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     26.760][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     26.760][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     26.840][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     26.840][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     26.840][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     26.855][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     26.875][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     26.875][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     26.945][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     26.945][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     26.945][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     26.945][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     27.035][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     27.035][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     27.035][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     27.045][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     27.075][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     27.075][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     27.135][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     27.135][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     27.135][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     27.135][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     28.415][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     28.415][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     28.935][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.315][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.315][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.315][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.315][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.315][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.520][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.520][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.520][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     34.665][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     34.665][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     34.665][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     34.675][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     34.695][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     34.695][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     34.765][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     34.765][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     34.765][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     34.765][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     34.855][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     34.855][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     34.855][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     34.865][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     34.885][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     34.885][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     34.955][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     34.955][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     34.955][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     34.955][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     35.035][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     35.035][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     35.035][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     35.045][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     35.065][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     35.065][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.135][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     35.135][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     35.135][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     35.135][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     35.230][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     35.230][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     35.230][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     35.240][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     35.260][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     35.260][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.330][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     35.330][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     35.330][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     35.330][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     36.560][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     36.560][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     37.080][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[     68.225][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     68.240][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     68.260][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     68.275][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     68.275][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[     68.275][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x1 pma_sig 0x1
[     68.290][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[     68.300][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     68.300][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[     68.300][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     68.300][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     68.300][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[     68.300][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     68.300][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     68.300][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[     68.300][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     68.300][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[     68.300][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[     68.300][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[     68.305][0-0][      0][  0][IMP-info]init intr aging 0
[     68.305][0-0][      0][  0][IMP-info]TM not bypass
[     68.305][0-0][      0][  0][IMP-info]not support l2 forward
[     68.305][0-0][      0][  0][IMP-info]flow director init mode 0
[     68.305][0-0][      0][  0][IMP-info]nic init success
[     68.305][0-0][      0][  0][IMP-info]rocee init success
[     68.305][0-0][      0][  0][IMP-info]imp_global_reset_handle end
[     68.305][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     68.305][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     68.305][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     68.305][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     71.615][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x3
[     71.615][0-0][      0][  0][IMP-info]cmdq 0x0, intr ageing 0
[     72.030][0-0][      0][  0][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     72.030][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x1) ret 0
[     72.030][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     72.055][0-0][      0][  0][IMP-info]mac 0 set loopback enable 0x0(mask 0x4) ret 0
[     72.090][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x3
[     72.090][0-0][      0][  0][IMP-info]cmdq 0x1, intr ageing 0
[     72.095][0-0][      0][  0][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     72.095][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x1) ret 0
[     72.095][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     72.125][0-0][      0][  0][IMP-info]mac 1 set loopback enable 0x0(mask 0x4) ret 0
[     72.170][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x3
[     72.170][0-0][      0][  0][IMP-info]cmdq 0x2, intr ageing 0
[     72.175][0-0][      0][  0][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     72.175][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x1) ret 0
[     72.175][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     72.195][0-0][      0][  0][IMP-info]mac 2 set loopback enable 0x0(mask 0x4) ret 0
[     72.230][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x3
[     72.230][0-0][      0][  0][IMP-info]cmdq 0x3, intr ageing 0
[     72.235][0-0][      0][  0][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     72.235][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x1) ret 0
[     72.235][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     72.275][0-0][      0][  0][IMP-info]mac 3 set loopback enable 0x0(mask 0x4) ret 0
[     87.450][0-0][      0][  0][IMP-info]pf 0 vf 0 eqc bt number 64 should not be larger than 3
[     87.495][0-0][      0][  0][IMP-info]pf 1 vf 0 eqc bt number 64 should not be larger than 3
[     87.545][0-0][      0][  0][IMP-info]pf 2 vf 0 eqc bt number 64 should not be larger than 3
[     87.590][0-0][      0][  0][IMP-info]pf 3 vf 0 eqc bt number 64 should not be larger than 3
[    123.725][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[    123.730][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[    123.740][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[    123.750][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[    124.240][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[    124.245][0-0][      0][  0][IMP-info]IMP report mac 1 link status 1, event 0
[    124.250][0-0][      0][  0][IMP-info]IMP report mac 2 link status 1, event 0
[    124.265][0-0][      0][  0][IMP-info]IMP report mac 3 link status 1, event 0
[    125.795][0-0][      0][  0][IMP-info]set user mac 0, speed 2 lanes 1(0) sds_rate 1(0) duplex 1(1).
[    125.795][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 2 lanes 1 sds_rate 1 fec 3 duplex 1
[    125.795][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[    125.795][0-0][      0][  0][IMP-info]present 0 mac_link 1 pcs_link 1 alos 0x0 pma_en 0x0 pma_sig 0x1
[    126.315][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[      0.000][0-0][      0][  0][IMP-info]systick init success
[      0.000][0-0][      0][  0][IMP-info]timer init success
[      0.000][0-0][      0][  0][IMP-info]watchdog inited success
[      0.000][0-0][      0][  0][IMP-info]Get cpld info from header, compatible = 1.
[      0.010][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]imp chip 0 die 0 mac 0 card 0x0 ncl init success
[      0.015][0-0][      0][  0][IMP-info]cpld id 0 i2c 0 dev 0x0 rw 0x2 init
[      0.015][0-0][      0][  0][IMP-info]mdio init success
[      0.015][0-0][      0][  0][IMP-info]sgpio init entry
[      0.055][0-0][      0][  0][IMP-info]bios setup init success.
[      0.055][0-0][      0][  0][IMP-info]hot plug init, type: support(0), current(0)
[      0.105][0-0][      0][  0][IMP-info]mac serdes mode 1 init success.
[      0.115][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[      0.115][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[      0.215][0-0][      0][  0][IMP-info]mac 0 phy init config 0
[      0.215][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[      0.215][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[      0.215][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[      0.215][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[      0.320][0-0][      0][  0][IMP-info]mac 1 phy init config 0
[      0.320][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[      0.320][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[      0.320][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[      0.320][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[      0.420][0-0][      0][  0][IMP-info]mac 2 phy init config 0
[      0.420][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[      0.420][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[      0.420][0-0][      0][  0][IMP-info]mac 3 init, pf 3 media type 2, phy_addr 7
[      0.420][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[      0.525][0-0][      0][  0][IMP-info]mac 3 phy init config 0
[      0.525][0-0][      0][  0][IMP-info]mac 3 link driver port type 2
[      0.525][0-0][      0][  0][IMP-info]mac_id 3 init used 1, port_type 2 roh 0 abi 0xe
[      0.525][0-0][      0][  0][IMP-info]init intr aging 0
[      0.525][0-0][      0][  0][IMP-info]TM not bypass
[      0.525][0-0][      0][  0][IMP-info]not support l2 forward
[      0.525][0-0][      0][  0][IMP-info]flow director init mode 0
[      0.525][0-0][      0][  0][IMP-info]nic init success
[      0.525][0-0][      0][  0][IMP-info]rocee init success
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x0
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x1
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x2
[      0.525][0-0][      0][  0][IMP-info]reset status:0x0, pf_id:0x3
[      0.525][0-0][      0][  0][IMP-info]imp version is 30a180d 
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[      0.525][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 2 abi 0xe, speed 3 lanes 1 sds_rate 1 fec 3 duplex 1
[     34.860][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x0, val 0x4
[     34.860][0-0][      0][  0][IMP-info]mac 0 link driver port type 3
[     34.860][0-0][      0][  0][IMP-info]mac 0 phy probe driver YT8521SH
[     34.870][0-0][      0][  1][IMP-info]set user mac 0, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     34.890][0-0][      0][  0][IMP-info]cmdq 0, process opcode 0x850, ret 5
[     34.890][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     34.960][0-0][      0][  0][IMP-info]mac 0 phy usage change to 1
[     34.960][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     34.960][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 1
[     34.960][0-0][      0][  0][IMP-info]mac link restart, mac 0, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     35.040][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x1, val 0x4
[     35.040][0-0][      0][  0][IMP-info]mac 1 link driver port type 3
[     35.040][0-0][      0][  0][IMP-info]mac 1 phy probe driver YT8521SH
[     35.055][0-0][      0][  1][IMP-info]set user mac 1, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     35.075][0-0][      0][  0][IMP-info]cmdq 1, process opcode 0x850, ret 5
[     35.075][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.145][0-0][      0][  0][IMP-info]mac 1 phy usage change to 1
[     35.145][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     35.145][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 1
[     35.145][0-0][      0][  0][IMP-info]mac link restart, mac 1, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     35.225][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x2, val 0x4
[     35.225][0-0][      0][  0][IMP-info]mac 2 link driver port type 3
[     35.225][0-0][      0][  0][IMP-info]mac 2 phy probe driver YT8521SH
[     35.235][0-0][      0][  1][IMP-info]set user mac 2, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     35.265][0-0][      0][  0][IMP-info]cmdq 2, process opcode 0x850, ret 5
[     35.265][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.325][0-0][      0][  0][IMP-info]mac 2 phy usage change to 1
[     35.325][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     35.325][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 1
[     35.325][0-0][      0][  0][IMP-info]mac link restart, mac 2, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     35.415][0-0][      0][  0][IMP-info]imp_driver compt cmdq 0x3, val 0x4
[     35.415][0-0][      0][  0][IMP-info]mac 3 link driver port type 3
[     35.415][0-0][      0][  0][IMP-info]mac 3 phy probe driver YT8521SH
[     35.430][0-0][      0][  1][IMP-info]set user mac 3, speed 3 lanes 1(0) sds_rate 1(0) duplex 1(1).
[     35.445][0-0][      0][  0][IMP-info]cmdq 3, process opcode 0x850, ret 5
[     35.445][0-0][      0][  0][IMP-error]imp cmd opcode = 0x1509 parse fail.
[     35.520][0-0][      0][  0][IMP-info]mac 3 phy usage change to 1
[     35.520][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     35.520][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 1
[     35.520][0-0][      0][  0][IMP-info]mac link restart, mac 3, wire 32 an 1 abi 0xf, speed 0 lanes 0 sds_rate 0 fec 0 duplex 0
[     36.815][0-0][      0][  0][IMP-info]mac 0 update phy speed 2 duplex 1
[     36.815][0-0][      0][  0][IMP-info]mac 0 mac_phy_update_pause set mac pause rx 1 tx 1
[     37.340][0-0][      0][  0][IMP-info]IMP report mac 0 link status 1, event 0
[     79.690][0-0][      0][  0][IMP-info]mac_id 3 (ncsi dis)set enable 0
[     79.705][0-0][      0][  0][IMP-info]mac_id 2 (ncsi dis)set enable 0
[     79.720][0-0][      0][  0][IMP-info]mac_id 1 (ncsi dis)set enable 0
[     79.740][0-0][      0][  0][IMP-info]mac_id 0 (ncsi dis)set enable 0
[     79.740][0-0][      0][  0][IMP-info]IMP report mac 0 link status 0, event 0
[     79.740][0-0][      0][  0][IMP-info]mac_link 1 pcs_link 1 phy_link 0 alos 0x0 pma_en 0x1 pma_sig 0x1
[     79.755][0-0][      0][  0][IMP-info]imp_global_reset_handle start
[     79.765][0-0][      0][  0][IMP-info]mac 0 init, pf 0 media type 2, phy_addr 1
[     79.765][0-0][      0][  0][IMP-info]mac 0 link driver port type 2
[     79.765][0-0][      0][  0][IMP-info]mac_id 0 init used 1, port_type 2 roh 0 abi 0xe
[     79.765][0-0][      0][  0][IMP-info]mac 1 init, pf 1 media type 2, phy_addr 3
[     79.765][0-0][      0][  0][IMP-info]mac 1 link driver port type 2
[     79.765][0-0][      0][  0][IMP-info]mac_id 1 init used 1, port_type 2 roh 0 abi 0xe
[     79.765][0-0][      0][  0][IMP-info]mac 2 init, pf 2 media type 2, phy_addr 5
[     79.765][0-0][      0][  0][IMP-info]mac 2 link driver port type 2
[     79.765][0-0][      0][  0][IMP-info]mac_id 2 init used 1, port_type 2 roh 0 abi 0xe
[     79.765][0-0][      0][  0][IMP-in