cat /proc/ekbox

EKbox head info:phyaddr=0x0000000084be0000, physize=0x1fffc, msgno=4
EKbox show message[0, 0x336a]:
                                                                                                                                                                                                                                                                
EKbox: kernel init success!
EKbox: memory init success!
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000024040000
[    0.000000] rcu: 	Offload RCU callbacks from CPUs: (none).
EKbox: irq init success!
[    0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.010005] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.010199] can't find led node, please check it
[    0.010209] Can't find led info in dtb,make sure there is no led on board
[    0.010447] Console: colour dummy device 80x25
EKbox: console init success!
[    0.010645] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[    0.010669] pid_max: default: 32768 minimum: 301
[    0.011085] LSM: Security Framework initializing
[    0.011118] Yama: becoming mindful.
[    0.011298] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.011324] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
EKbox: SVN Last Changed Rev: 20251215152335
EKbox: mastercore load success!
[    0.014579] early_panic_init: Missing panic_core_isolate device node.
[    0.015466] rcu: Hierarchical SRCU implementation.
[    0.016049] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.016208] EFI services will not be available.
[    0.016239] page_attr_early_init succeed
[    0.016961] smp: Bringing up secondary CPUs ...
EKbox: slavecore1 load success!
EKbox: slavecore2 load success!
EKbox: slavecore3 load success!
[    0.018372] Detected VIPT I-cache on CPU1
[    0.018423] GICv3: CPU1: found redistributor 100 region 0:0x0000000024060000
[    0.018501] CPU1: Booted secondary processor 0x0000000100 [0x411fd050]
[    0.020184] Detected VIPT I-cache on CPU2
[    0.020223] GICv3: CPU2: found redistributor 200 region 0:0x0000000024080000
[    0.020288] CPU2: Booted secondary processor 0x0000000200 [0x411fd050]
[    0.021742] Detected VIPT I-cache on CPU3
[    0.021777] GICv3: CPU3: found redistributor 300 region 0:0x00000000240a0000
[    0.021838] CPU3: Booted secondary processor 0x0000000300 [0x411fd050]
[    0.022005] smp: Brought up 1 node, 4 CPUs
[    0.022062] SMP: Total of 4 processors activated.
[    0.022074] CPU features: detected: Privileged Access Never
[    0.022083] CPU features: detected: 32-bit EL0 Support
[    0.022092] CPU features: detected: Common not Private translations
[    0.022101] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.022111] CPU features: detected: CRC32 instructions
[    0.022119] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.022128] CPU features: detected: 32-bit EL1 Support
[    0.022138] CPU features: detected: RCpc load-acquire (LDAPR)
[    0.022860] CPU: All CPU(s) started at EL2
[    0.022928] alternatives: patching kernel code
[    0.024280] devtmpfs: initialized
[    0.028867] KASLR enabled
[    0.029712] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.029763] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.029972] kworker/u8:0 (32) used greatest stack depth: 12992 bytes left
[    0.030566] pinctrl core: initialized pinctrl subsystem
[    0.032871] DMI not present or invalid.
[    0.032958] softdog_kthread_create
[    0.033849] NET: Registered protocol family 16
[    0.034955] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.035049] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.035179] audit: initializing netlink subsys (disabled)
[    0.035404] audit cpu affinity init success
[    0.035512] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1
[    0.039844] thermal_sys: Registered thermal governor 'step_wise'
[    0.040555] cpuidle: using governor ladder
[    0.040617] cpuidle: using governor menu
[    0.040820] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.041004] ASID allocator initialised with 65536 entries
[    0.041752] Serial: AMBA PL011 UART driver
[    0.129119] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.129148] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.129160] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.129172] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.138524] ACPI: Interpreter disabled.
[    0.138665] iommu: Default domain type: Translated 
[    0.140227] NetLabel: Initializing
[    0.140262] NetLabel:  domain hash size = 128
[    0.140272] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.140485] NetLabel:  unlabeled traffic allowed by default
[    0.141254] clocksource: Switched to clocksource arch_sys_counter
[    0.182571] VFS: Disk quotas dquot_6.6.0
[    0.182682] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.183576] pnp: PnP ACPI: disabled
[    0.202640] NET: Registered protocol family 2
[    0.202931] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.205041] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 40960 bytes, linear)
[    0.205105] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.205170] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.205336] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[    0.205561] TCP: Hash tables configured (established 16384 bind 16384)
[    0.205749] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.205864] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.206239] NET: Registered protocol family 1
[    0.206297] PCI: CLS 0 bytes, default 64
[    0.206580] Trying to unpack rootfs image as initramfs...
[    0.435654] Freeing initrd memory: 5120K
[    0.436331] kvm [1]: KVM ncsnp disabled
[    0.436350] kvm [1]: KVM dvmbm disabled
[    0.436387] kvm [1]: IPA Size Limit: 40 bits
[    0.437421] kvm [1]: GICv3: no GICV resource entry
[    0.437437] kvm [1]: disabling GICv2 emulation
[    0.437472] kvm [1]: GIC system register CPU interface enabled
[    0.437720] kvm [1]: vgic interrupt IRQ16
[    0.437965] kvm [1]: Hyp mode initialized successfully
[    0.442204] modsign: There is no certification file
[    0.442232] modsign: There is only one cert or no cert
[    0.442242] Initialise system trusted keyrings
[    0.443162] workingset: timestamp_bits=43 max_order=19 bucket_order=0
[    0.456336] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.456779] Huawei Secure C library init
[    0.456802] cms cbb init
[    0.457165] modsign: create major 250 for module crl devs
[    0.499581] Key type asymmetric registered
[    0.499610] Asymmetric key parser 'x509' registered
[    0.499705] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.499983] io scheduler mq-deadline registered
[    0.652068] create /sys/kernel/tty_status_trace succ.
[    0.652140] did not found ttyname.
[    0.652153] default tty_suspend_mode is 0.
[    0.652165] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.652388] Serial: 8250/16550 suspend register ok.
[    0.652407] get_tty_suspend_info: mode is 0
[    0.655706] printk: console [ttyS0] disabled
[    0.655826] 8710000.uart: ttyS0 at MMIO 0x8710000 (irq = 23, base_baud = 6250000) is a 16550A
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050]
[    0.000000] Linux version 5.10.0 (oe-user@oe-host) (aarch64-euler-linux-gcc (BiSheng Embedded CPU 303.1.0.B010) 7.3.0, GNU ld (BiSheng Embedded CPU 303.1.0.B010) 2.41) #1 SMP PREEMPT Mon Dec 15 15:23:35 CST 2025
[    0.000000] Machine model: Hisilicon Hi1711 ASIC
[    0.000000] efi: UEFI not found.
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xeffe6640-0xeffe7fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000084be0000-0x0000000084bfefff]
[    0.000000]   node   0: [mem 0x0000000087200000-0x00000000efffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] On node 0 totalpages: 429599
[    0.000000]   DMA zone: 6865 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 429599 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.5
[    0.000000] [dts]:cpu type is 1711
[    0.000000] can't find led ctrl node, please check it
[    0.000000] percpu: Embedded 30 pages/cpu s85224 r8192 d29464 u122880
[    0.000000] pcpu-alloc: s85224 r8192 d29464 u122880 alloc=30*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 422734
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=ttyS0,115200n8N earlycon=uart8250,mmio32,0x08710000 initrd=${initrd_load_addr},${initrd_size} rdinit=/sbin/init rw ekbox=0x20000$0x84be0000 kbox_mem=0x2e0000@0x84900000 swift_irqsoff_enable swxn=1
[    0.000000] Fallback order for Node 0: 0 
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 13912(84%)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1666672K/1718396K available (7808K kernel code, 926K rwdata, 1516K rodata, 1856K init, 2377K bss, 51724K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] kmemleak: Kernel memory leak detector disabled
[    0.656371] printk: console [ttyS0] enabled
[    0.658494] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.676433] brd: module loaded
[    0.684709] loop: module loaded
[    0.686834] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.687447] fiq_glue_parse_source_common fiq source is 1!
[    0.687470] fiq_glue_parse_type_common fiq type is 0!
[    0.687481] fiq_glue_parse_buffer_offset_type fiq get cpu id type is default!
[    0.687494] fiq_glue_parse_clean_wdt fiq clean-wdt is 0!
[    0.687503] fiq_glue_parse_dead_loop fiq dead-loop is 1!
[    0.687514] fiq_glue_parse_invalid_cache fiq invalid-cache is 1!
[    0.687523] fiq_glue_parse_use_atf_under_same_image fiq use-atf-under-same-image is 0!
[    0.687534] fiq_glue_no_info_init fiq_num is 1, fiq_num_max is 16
[    0.687544] fiq_glue_no_info_init i 0 fiq-no 141
[    0.689228] KBOX: ddrram: fs magic not match. It's ok if first time using this device
[    0.697125] KBOX: kbox_exception_dump_valid abort for NULL dump_path!
[    0.704944] KBOX: kbox:create region panic, size=65536
EKbox: ------------------starting reboot !------------------
EKbox: [UTC][2026.04.02 05:43:00-291231880][Clock][9319302719600]
EKbox: [__do_sys_reboot:359]
EKbox: [kernel_restart:253]
EKbox: [kernel_restart_prepare:78]
EKbox: [kernel_restart_prepare:83]
EKbox: [machine_restart:237]

EKbox head info:phyaddr=0x0000000084be0000, physize=0x1fffc, msgno=4
EKbox show message[1, 0x32c8]:
                                                                                                                                                                                                                                                                
EKbox: kernel init success!
EKbox: memory init success!
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000024040000
[    0.000000] rcu: 	Offload RCU callbacks from CPUs: (none).
EKbox: irq init success!
[    0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.010006] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.010200] can't find led node, please check it
[    0.010210] Can't find led info in dtb,make sure there is no led on board
[    0.010449] Console: colour dummy device 80x25
EKbox: console init success!
[    0.010652] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[    0.010676] pid_max: default: 32768 minimum: 301
[    0.011099] LSM: Security Framework initializing
[    0.011135] Yama: becoming mindful.
[    0.011320] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.011347] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
EKbox: SVN Last Changed Rev: 20251215152335
EKbox: mastercore load success!
[    0.014671] early_panic_init: Missing panic_core_isolate device node.
[    0.015591] rcu: Hierarchical SRCU implementation.
[    0.016199] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.016363] EFI services will not be available.
[    0.016395] page_attr_early_init succeed
[    0.017144] smp: Bringing up secondary CPUs ...
EKbox: slavecore1 load success!
EKbox: slavecore2 load success!
EKbox: slavecore3 load success!
[    0.018582] Detected VIPT I-cache on CPU1
[    0.018633] GICv3: CPU1: found redistributor 100 region 0:0x0000000024060000
[    0.018714] CPU1: Booted secondary processor 0x0000000100 [0x411fd050]
[    0.020478] Detected VIPT I-cache on CPU2
[    0.020517] GICv3: CPU2: found redistributor 200 region 0:0x0000000024080000
[    0.020583] CPU2: Booted secondary processor 0x0000000200 [0x411fd050]
[    0.022072] Detected VIPT I-cache on CPU3
[    0.022109] GICv3: CPU3: found redistributor 300 region 0:0x00000000240a0000
[    0.022172] CPU3: Booted secondary processor 0x0000000300 [0x411fd050]
[    0.022351] smp: Brought up 1 node, 4 CPUs
[    0.022410] SMP: Total of 4 processors activated.
[    0.022422] CPU features: detected: Privileged Access Never
[    0.022431] CPU features: detected: 32-bit EL0 Support
[    0.022441] CPU features: detected: Common not Private translations
[    0.022451] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.022460] CPU features: detected: CRC32 instructions
[    0.022468] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.022477] CPU features: detected: 32-bit EL1 Support
[    0.022488] CPU features: detected: RCpc load-acquire (LDAPR)
[    0.023218] CPU: All CPU(s) started at EL2
[    0.023290] alternatives: patching kernel code
[    0.024661] devtmpfs: initialized
[    0.029274] KASLR enabled
[    0.030193] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.030236] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.030404] kworker/u8:0 (32) used greatest stack depth: 12992 bytes left
[    0.030980] pinctrl core: initialized pinctrl subsystem
[    0.033318] DMI not present or invalid.
[    0.033407] softdog_kthread_create
[    0.034310] NET: Registered protocol family 16
[    0.035427] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.035523] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.035652] audit: initializing netlink subsys (disabled)
[    0.035882] audit cpu affinity init success
[    0.035989] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1
[    0.040454] thermal_sys: Registered thermal governor 'step_wise'
[    0.041119] cpuidle: using governor ladder
[    0.041181] cpuidle: using governor menu
[    0.041387] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.041581] ASID allocator initialised with 65536 entries
[    0.042336] Serial: AMBA PL011 UART driver
[    0.114419] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.114446] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.114457] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.114468] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.119470] ACPI: Interpreter disabled.
[    0.119589] iommu: Default domain type: Translated 
[    0.121272] NetLabel: Initializing
[    0.121302] NetLabel:  domain hash size = 128
[    0.121311] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.121419] NetLabel:  unlabeled traffic allowed by default
[    0.122120] clocksource: Switched to clocksource arch_sys_counter
[    0.163868] VFS: Disk quotas dquot_6.6.0
[    0.163983] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.164831] pnp: PnP ACPI: disabled
[    0.203031] NET: Registered protocol family 2
[    0.203329] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.205456] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 40960 bytes, linear)
[    0.205520] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.205588] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.205753] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[    0.205980] TCP: Hash tables configured (established 16384 bind 16384)
[    0.206225] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.206342] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.206717] NET: Registered protocol family 1
[    0.206774] PCI: CLS 0 bytes, default 64
[    0.207077] Trying to unpack rootfs image as initramfs...
[    0.436637] Freeing initrd memory: 5120K
[    0.437248] kvm [1]: KVM ncsnp disabled
[    0.437268] kvm [1]: KVM dvmbm disabled
[    0.437305] kvm [1]: IPA Size Limit: 40 bits
[    0.438342] kvm [1]: GICv3: no GICV resource entry
[    0.438356] kvm [1]: disabling GICv2 emulation
[    0.438391] kvm [1]: GIC system register CPU interface enabled
[    0.438605] kvm [1]: vgic interrupt IRQ16
[    0.438850] kvm [1]: Hyp mode initialized successfully
[    0.443274] modsign: There is no certification file
[    0.443307] modsign: There is only one cert or no cert
[    0.443317] Initialise system trusted keyrings
[    0.443769] workingset: timestamp_bits=43 max_order=19 bucket_order=0
[    0.456986] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.457423] Huawei Secure C library init
[    0.457447] cms cbb init
[    0.457802] modsign: create major 250 for module crl devs
[    0.500963] Key type asymmetric registered
[    0.500994] Asymmetric key parser 'x509' registered
[    0.501089] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.501360] io scheduler mq-deadline registered
[    0.661278] create /sys/kernel/tty_status_trace succ.
[    0.661339] did not found ttyname.
[    0.661350] default tty_suspend_mode is 0.
[    0.661362] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.661596] Serial: 8250/16550 suspend register ok.
[    0.661615] get_tty_suspend_info: mode is 0
[    0.665470] printk: console [ttyS0] disabled
[    0.665599] 8710000.uart: ttyS0 at MMIO 0x8710000 (irq = 23, base_baud = 6250000) is a 16550A
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050]
[    0.000000] Linux version 5.10.0 (oe-user@oe-host) (aarch64-euler-linux-gcc (BiSheng Embedded CPU 303.1.0.B010) 7.3.0, GNU ld (BiSheng Embedded CPU 303.1.0.B010) 2.41) #1 SMP PREEMPT Mon Dec 15 15:23:35 CST 2025
[    0.000000] Machine model: Hisilicon Hi1711 ASIC
[    0.000000] efi: UEFI not found.
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xeffe6640-0xeffe7fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000084be0000-0x0000000084bfefff]
[    0.000000]   node   0: [mem 0x0000000087200000-0x00000000efffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] On node 0 totalpages: 429599
[    0.000000]   DMA zone: 6865 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 429599 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.5
[    0.000000] [dts]:cpu type is 1711
[    0.000000] can't find led ctrl node, please check it
[    0.000000] percpu: Embedded 30 pages/cpu s85224 r8192 d29464 u122880
[    0.000000] pcpu-alloc: s85224 r8192 d29464 u122880 alloc=30*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 422734
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=ttyS0,115200n8N earlycon=uart8250,mmio32,0x08710000 initrd=${initrd_load_addr},${initrd_size} rdinit=/sbin/init rw ekbox=0x20000$0x84be0000 kbox_mem=0x2e0000@0x84900000 swift_irqsoff_enable swxn=1
[    0.000000] Fallback order for Node 0: 0 
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 13912(84%)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1666672K/1718396K available (7808K kernel code, 926K rwdata, 1516K rodata, 1856K init, 2377K bss, 51724K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] kmemleak: Kernel memory leak detector disabled
[    0.666143] printk: console [ttyS0] enabled
[    0.669954] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.696320] brd: module loaded
[    0.708996] loop: module loaded
[    0.712442] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.713555] fiq_glue_parse_source_common fiq source is 1!
[    0.713585] fiq_glue_parse_type_common fiq type is 0!
[    0.713597] fiq_glue_parse_buffer_offset_type fiq get cpu id type is default!
[    0.713610] fiq_glue_parse_clean_wdt fiq clean-wdt is 0!
[    0.713620] fiq_glue_parse_dead_loop fiq dead-loop is 1!
[    0.713629] fiq_glue_parse_invalid_cache fiq invalid-cache is 1!
[    0.713639] fiq_glue_parse_use_atf_under_same_image fiq use-atf-under-same-image is 0!
[    0.713649] fiq_glue_no_info_init fiq_num is 1, fiq_num_max is 16
[    0.713660] fiq_glue_no_info_init i 0 fiq-no 141
[    0.716529] KBOX: kbox:create region panic, size=65536
EKbox: ------------------starting reboot !------------------
EKbox: [UTC][2026.04.02 06:03:21-760972920][Clock][1190773594480]
EKbox: [__do_sys_reboot:359]
EKbox: [kernel_restart:253]
EKbox: [kernel_restart_prepare:78]
EKbox: [kernel_restart_prepare:83]
EKbox: [machine_restart:237]

EKbox head info:phyaddr=0x0000000084be0000, physize=0x1fffc, msgno=4
EKbox show message[2, 0x3316]:
                                                                                                                                                                                                                                                                
EKbox: kernel init success!
EKbox: memory init success!
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000024040000
[    0.000000] rcu: 	Offload RCU callbacks from CPUs: (none).
EKbox: irq init success!
[    0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.010006] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.010201] can't find led node, please check it
[    0.010211] Can't find led info in dtb,make sure there is no led on board
[    0.010454] Console: colour dummy device 80x25
EKbox: console init success!
[    0.010652] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[    0.010675] pid_max: default: 32768 minimum: 301
[    0.011096] LSM: Security Framework initializing
[    0.011130] Yama: becoming mindful.
[    0.011308] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.011332] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
EKbox: SVN Last Changed Rev: 20251215152335
EKbox: mastercore load success!
[    0.014667] early_panic_init: Missing panic_core_isolate device node.
[    0.015586] rcu: Hierarchical SRCU implementation.
[    0.016193] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.016358] EFI services will not be available.
[    0.016391] page_attr_early_init succeed
[    0.017130] smp: Bringing up secondary CPUs ...
EKbox: slavecore1 load success!
EKbox: slavecore2 load success!
EKbox: slavecore3 load success!
[    0.018595] Detected VIPT I-cache on CPU1
[    0.018646] GICv3: CPU1: found redistributor 100 region 0:0x0000000024060000
[    0.018727] CPU1: Booted secondary processor 0x0000000100 [0x411fd050]
[    0.020490] Detected VIPT I-cache on CPU2
[    0.020529] GICv3: CPU2: found redistributor 200 region 0:0x0000000024080000
[    0.020596] CPU2: Booted secondary processor 0x0000000200 [0x411fd050]
[    0.022083] Detected VIPT I-cache on CPU3
[    0.022120] GICv3: CPU3: found redistributor 300 region 0:0x00000000240a0000
[    0.022182] CPU3: Booted secondary processor 0x0000000300 [0x411fd050]
[    0.022349] smp: Brought up 1 node, 4 CPUs
[    0.022406] SMP: Total of 4 processors activated.
[    0.022418] CPU features: detected: Privileged Access Never
[    0.022428] CPU features: detected: 32-bit EL0 Support
[    0.022437] CPU features: detected: Common not Private translations
[    0.022446] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.022456] CPU features: detected: CRC32 instructions
[    0.022464] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.022473] CPU features: detected: 32-bit EL1 Support
[    0.022483] CPU features: detected: RCpc load-acquire (LDAPR)
[    0.023211] CPU: All CPU(s) started at EL2
[    0.023283] alternatives: patching kernel code
[    0.024649] devtmpfs: initialized
[    0.029258] KASLR enabled
[    0.030177] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.030219] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.030386] kworker/u8:0 (32) used greatest stack depth: 12992 bytes left
[    0.030966] pinctrl core: initialized pinctrl subsystem
[    0.033316] DMI not present or invalid.
[    0.033406] softdog_kthread_create
[    0.034307] NET: Registered protocol family 16
[    0.035418] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.035514] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.035645] audit: initializing netlink subsys (disabled)
[    0.035878] audit cpu affinity init success
[    0.035983] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1
[    0.040445] thermal_sys: Registered thermal governor 'step_wise'
[    0.041108] cpuidle: using governor ladder
[    0.041170] cpuidle: using governor menu
[    0.041377] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.041565] ASID allocator initialised with 65536 entries
[    0.042309] Serial: AMBA PL011 UART driver
[    0.129390] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.129419] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.129430] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.129441] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.137417] ACPI: Interpreter disabled.
[    0.137562] iommu: Default domain type: Translated 
[    0.139025] NetLabel: Initializing
[    0.139054] NetLabel:  domain hash size = 128
[    0.139064] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.139172] NetLabel:  unlabeled traffic allowed by default
[    0.140319] clocksource: Switched to clocksource arch_sys_counter
[    0.181629] VFS: Disk quotas dquot_6.6.0
[    0.181744] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.182554] pnp: PnP ACPI: disabled
[    0.203849] NET: Registered protocol family 2
[    0.204128] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.206254] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 40960 bytes, linear)
[    0.206317] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.206380] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.206545] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[    0.206772] TCP: Hash tables configured (established 16384 bind 16384)
[    0.206965] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.207082] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.207437] NET: Registered protocol family 1
[    0.207494] PCI: CLS 0 bytes, default 64
[    0.207766] Trying to unpack rootfs image as initramfs...
[    0.436773] Freeing initrd memory: 5120K
[    0.437431] kvm [1]: KVM ncsnp disabled
[    0.437450] kvm [1]: KVM dvmbm disabled
[    0.437488] kvm [1]: IPA Size Limit: 40 bits
[    0.438522] kvm [1]: GICv3: no GICV resource entry
[    0.438539] kvm [1]: disabling GICv2 emulation
[    0.438575] kvm [1]: GIC system register CPU interface enabled
[    0.438825] kvm [1]: vgic interrupt IRQ16
[    0.439078] kvm [1]: Hyp mode initialized successfully
[    0.443488] modsign: There is no certification file
[    0.443520] modsign: There is only one cert or no cert
[    0.443529] Initialise system trusted keyrings
[    0.444306] workingset: timestamp_bits=43 max_order=19 bucket_order=0
[    0.457399] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.457870] Huawei Secure C library init
[    0.457894] cms cbb init
[    0.458299] modsign: create major 250 for module crl devs
[    0.501722] Key type asymmetric registered
[    0.501753] Asymmetric key parser 'x509' registered
[    0.501883] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.502202] io scheduler mq-deadline registered
[    0.588999] kworker/u8:2 (850) used greatest stack depth: 12784 bytes left
[    0.629128] create /sys/kernel/tty_status_trace succ.
[    0.629188] did not found ttyname.
[    0.629200] default tty_suspend_mode is 0.
[    0.629211] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.629428] Serial: 8250/16550 suspend register ok.
[    0.629448] get_tty_suspend_info: mode is 0
[    0.632975] printk: console [ttyS0] disabled
[    0.633096] 8710000.uart: ttyS0 at MMIO 0x8710000 (irq = 23, base_baud = 6250000) is a 16550A
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050]
[    0.000000] Linux version 5.10.0 (oe-user@oe-host) (aarch64-euler-linux-gcc (BiSheng Embedded CPU 303.1.0.B010) 7.3.0, GNU ld (BiSheng Embedded CPU 303.1.0.B010) 2.41) #1 SMP PREEMPT Mon Dec 15 15:23:35 CST 2025
[    0.000000] Machine model: Hisilicon Hi1711 ASIC
[    0.000000] efi: UEFI not found.
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xeffe6640-0xeffe7fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000084be0000-0x0000000084bfefff]
[    0.000000]   node   0: [mem 0x0000000087200000-0x00000000efffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] On node 0 totalpages: 429599
[    0.000000]   DMA zone: 6865 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 429599 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.5
[    0.000000] [dts]:cpu type is 1711
[    0.000000] can't find led ctrl node, please check it
[    0.000000] percpu: Embedded 30 pages/cpu s85224 r8192 d29464 u122880
[    0.000000] pcpu-alloc: s85224 r8192 d29464 u122880 alloc=30*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 422734
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=ttyS0,115200n8N earlycon=uart8250,mmio32,0x08710000 initrd=${initrd_load_addr},${initrd_size} rdinit=/sbin/init rw ekbox=0x20000$0x84be0000 kbox_mem=0x2e0000@0x84900000 swift_irqsoff_enable swxn=1
[    0.000000] Fallback order for Node 0: 0 
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 13912(84%)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1666672K/1718396K available (7808K kernel code, 926K rwdata, 1516K rodata, 1856K init, 2377K bss, 51724K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] kmemleak: Kernel memory leak detector disabled
[    0.633645] printk: console [ttyS0] enabled
[    0.635735] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.653981] brd: module loaded
[    0.662341] loop: module loaded
[    0.664471] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.665105] fiq_glue_parse_source_common fiq source is 1!
[    0.665129] fiq_glue_parse_type_common fiq type is 0!
[    0.665140] fiq_glue_parse_buffer_offset_type fiq get cpu id type is default!
[    0.665152] fiq_glue_parse_clean_wdt fiq clean-wdt is 0!
[    0.665162] fiq_glue_parse_dead_loop fiq dead-loop is 1!
[    0.665172] fiq_glue_parse_invalid_cache fiq invalid-cache is 1!
[    0.665182] fiq_glue_parse_use_atf_under_same_image fiq use-atf-under-same-image is 0!
[    0.665193] fiq_glue_no_info_init fiq_num is 1, fiq_num_max is 16
[    0.665204] fiq_glue_no_info_init i 0 fiq-no 141
[    0.666913] KBOX: kbox:create region panic, size=65536
EKbox: ------------------starting reboot !------------------
EKbox: [UTC][2026.04.02 07:34:54-409083920][Clock][5461441610960]
EKbox: [__do_sys_reboot:359]
EKbox: [kernel_restart:253]
EKbox: [kernel_restart_prepare:78]
EKbox: [kernel_restart_prepare:83]
EKbox: [machine_restart:237]

EKbox head info:phyaddr=0x0000000084be0000, physize=0x1fffc, msgno=4
EKbox show message[3, 0x32ca]:
                                                                                                                                                                                                                                                                
EKbox: kernel init success!
EKbox: memory init success!
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000024040000
[    0.000000] rcu: 	Offload RCU callbacks from CPUs: (none).
EKbox: irq init success!
[    0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.010005] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.010198] can't find led node, please check it
[    0.010209] Can't find led info in dtb,make sure there is no led on board
[    0.010444] Console: colour dummy device 80x25
EKbox: console init success!
[    0.010639] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[    0.010662] pid_max: default: 32768 minimum: 301
[    0.011082] LSM: Security Framework initializing
[    0.011117] Yama: becoming mindful.
[    0.011300] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.011326] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
EKbox: SVN Last Changed Rev: 20251215152335
EKbox: mastercore load success!
[    0.014639] early_panic_init: Missing panic_core_isolate device node.
[    0.015570] rcu: Hierarchical SRCU implementation.
[    0.016188] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.016347] EFI services will not be available.
[    0.016381] page_attr_early_init succeed
[    0.017133] smp: Bringing up secondary CPUs ...
EKbox: slavecore1 load success!
EKbox: slavecore2 load success!
EKbox: slavecore3 load success!
[    0.018590] Detected VIPT I-cache on CPU1
[    0.018640] GICv3: CPU1: found redistributor 100 region 0:0x0000000024060000
[    0.018721] CPU1: Booted secondary processor 0x0000000100 [0x411fd050]
[    0.020498] Detected VIPT I-cache on CPU2
[    0.020538] GICv3: CPU2: found redistributor 200 region 0:0x0000000024080000
[    0.020605] CPU2: Booted secondary processor 0x0000000200 [0x411fd050]
[    0.022117] Detected VIPT I-cache on CPU3
[    0.022154] GICv3: CPU3: found redistributor 300 region 0:0x00000000240a0000
[    0.022214] CPU3: Booted secondary processor 0x0000000300 [0x411fd050]
[    0.022390] smp: Brought up 1 node, 4 CPUs
[    0.022449] SMP: Total of 4 processors activated.
[    0.022460] CPU features: detected: Privileged Access Never
[    0.022469] CPU features: detected: 32-bit EL0 Support
[    0.022478] CPU features: detected: Common not Private translations
[    0.022488] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.022497] CPU features: detected: CRC32 instructions
[    0.022505] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.022515] CPU features: detected: 32-bit EL1 Support
[    0.022525] CPU features: detected: RCpc load-acquire (LDAPR)
[    0.023253] CPU: All CPU(s) started at EL2
[    0.023324] alternatives: patching kernel code
[    0.024695] devtmpfs: initialized
[    0.029312] KASLR enabled
[    0.030217] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.030259] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.030426] kworker/u8:0 (32) used greatest stack depth: 12992 bytes left
[    0.031001] pinctrl core: initialized pinctrl subsystem
[    0.033343] DMI not present or invalid.
[    0.033433] softdog_kthread_create
[    0.034334] NET: Registered protocol family 16
[    0.035443] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.035540] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.035671] audit: initializing netlink subsys (disabled)
[    0.035906] audit cpu affinity init success
[    0.036013] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1
[    0.040485] thermal_sys: Registered thermal governor 'step_wise'
[    0.041142] cpuidle: using governor ladder
[    0.041204] cpuidle: using governor menu
[    0.041406] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.041591] ASID allocator initialised with 65536 entries
[    0.042342] Serial: AMBA PL011 UART driver
[    0.125848] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.125876] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.125887] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.125898] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.130800] ACPI: Interpreter disabled.
[    0.131024] iommu: Default domain type: Translated 
[    0.132557] NetLabel: Initializing
[    0.132587] NetLabel:  domain hash size = 128
[    0.132597] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.132701] NetLabel:  unlabeled traffic allowed by default
[    0.133458] clocksource: Switched to clocksource arch_sys_counter
[    0.175531] VFS: Disk quotas dquot_6.6.0
[    0.175642] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.176540] pnp: PnP ACPI: disabled
[    0.195795] NET: Registered protocol family 2
[    0.196088] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.198247] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 40960 bytes, linear)
[    0.198312] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.198411] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.198557] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[    0.198782] TCP: Hash tables configured (established 16384 bind 16384)
[    0.198982] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.199099] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.199486] NET: Registered protocol family 1
[    0.199542] PCI: CLS 0 bytes, default 64
[    0.199832] Trying to unpack rootfs image as initramfs...
[    0.429257] Freeing initrd memory: 5120K
[    0.429926] kvm [1]: KVM ncsnp disabled
[    0.429946] kvm [1]: KVM dvmbm disabled
[    0.429983] kvm [1]: IPA Size Limit: 40 bits
[    0.430996] kvm [1]: GICv3: no GICV resource entry
[    0.431011] kvm [1]: disabling GICv2 emulation
[    0.431046] kvm [1]: GIC system register CPU interface enabled
[    0.431259] kvm [1]: vgic interrupt IRQ16
[    0.431502] kvm [1]: Hyp mode initialized successfully
[    0.435806] modsign: There is no certification file
[    0.435840] modsign: There is only one cert or no cert
[    0.435851] Initialise system trusted keyrings
[    0.436643] workingset: timestamp_bits=43 max_order=19 bucket_order=0
[    0.449813] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.450245] Huawei Secure C library init
[    0.450268] cms cbb init
[    0.450638] modsign: create major 250 for module crl devs
[    0.494307] Key type asymmetric registered
[    0.494338] Asymmetric key parser 'x509' registered
[    0.494433] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.494744] io scheduler mq-deadline registered
[    0.647437] create /sys/kernel/tty_status_trace succ.
[    0.647506] did not found ttyname.
[    0.647518] default tty_suspend_mode is 0.
[    0.647530] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.647714] Serial: 8250/16550 suspend register ok.
[    0.647733] get_tty_suspend_info: mode is 0
[    0.651092] printk: console [ttyS0] disabled
[    0.651217] 8710000.uart: ttyS0 at MMIO 0x8710000 (irq = 23, base_baud = 6250000) is a 16550A
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050]
[    0.000000] Linux version 5.10.0 (oe-user@oe-host) (aarch64-euler-linux-gcc (BiSheng Embedded CPU 303.1.0.B010) 7.3.0, GNU ld (BiSheng Embedded CPU 303.1.0.B010) 2.41) #1 SMP PREEMPT Mon Dec 15 15:23:35 CST 2025
[    0.000000] Machine model: Hisilicon Hi1711 ASIC
[    0.000000] efi: UEFI not found.
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xeffe6640-0xeffe7fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000084be0000-0x0000000084bfefff]
[    0.000000]   node   0: [mem 0x0000000087200000-0x00000000efffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] On node 0 totalpages: 429599
[    0.000000]   DMA zone: 6865 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 429599 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.5
[    0.000000] [dts]:cpu type is 1711
[    0.000000] can't find led ctrl node, please check it
[    0.000000] percpu: Embedded 30 pages/cpu s85224 r8192 d29464 u122880
[    0.000000] pcpu-alloc: s85224 r8192 d29464 u122880 alloc=30*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 422734
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=ttyS0,115200n8N earlycon=uart8250,mmio32,0x08710000 initrd=${initrd_load_addr},${initrd_size} rdinit=/sbin/init rw ekbox=0x20000$0x84be0000 kbox_mem=0x2e0000@0x84900000 swift_irqsoff_enable swxn=1
[    0.000000] Fallback order for Node 0: 0 
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 13912(84%)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1666672K/1718396K available (7808K kernel code, 926K rwdata, 1516K rodata, 1856K init, 2377K bss, 51724K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] kmemleak: Kernel memory leak detector disabled
[    0.651743] printk: console [ttyS0] enabled
[    0.654576] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.672311] brd: module loaded
[    0.680416] loop: module loaded
[    0.682551] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.683180] fiq_glue_parse_source_common fiq source is 1!
[    0.683204] fiq_glue_parse_type_common fiq type is 0!
[    0.683217] fiq_glue_parse_buffer_offset_type fiq get cpu id type is default!
[    0.683229] fiq_glue_parse_clean_wdt fiq clean-wdt is 0!
[    0.683239] fiq_glue_parse_dead_loop fiq dead-loop is 1!
[    0.683248] fiq_glue_parse_invalid_cache fiq invalid-cache is 1!
[    0.683258] fiq_glue_parse_use_atf_under_same_image fiq use-atf-under-same-image is 0!
[    0.683269] fiq_glue_no_info_init fiq_num is 1, fiq_num_max is 16
[    0.683279] fiq_glue_no_info_init i 0 fiq-no 141
[    0.685325] KBOX: kbox:create region panic, size=65536
EKbox: ------------------starting reboot !------------------
EKbox: [UTC][2026.04.07 08:47:03-128665040][Clock][436287144691000]
EKbox: [__do_sys_reboot:359]
EKbox: [kernel_restart:253]
EKbox: [kernel_restart_prepare:78]
EKbox: [kernel_restart_prepare:83]
EKbox: [machine_restart:237]

EKbox head info:phyaddr=0x0000000084be0000, physize=0x1fffc, msgno=4
EKbox show message[4, 0x31ad]:
                                                                                                                                                                                                                                                                
EKbox: kernel init success!
EKbox: memory init success!
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu: 	RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 256 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000024040000
[    0.000000] rcu: 	Offload RCU callbacks from CPUs: (none).
EKbox: irq init success!
[    0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns
[    0.010005] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns
[    0.010199] can't find led node, please check it
[    0.010210] Can't find led info in dtb,make sure there is no led on board
[    0.010442] Console: colour dummy device 80x25
EKbox: console init success!
[    0.010641] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[    0.010663] pid_max: default: 32768 minimum: 301
[    0.011086] LSM: Security Framework initializing
[    0.011119] Yama: becoming mindful.
[    0.011297] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.011322] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
EKbox: SVN Last Changed Rev: 20251215152335
EKbox: mastercore load success!
[    0.014577] early_panic_init: Missing panic_core_isolate device node.
[    0.015477] rcu: Hierarchical SRCU implementation.
[    0.016073] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.016231] EFI services will not be available.
[    0.016264] page_attr_early_init succeed
[    0.016978] smp: Bringing up secondary CPUs ...
EKbox: slavecore1 load success!
EKbox: slavecore2 load success!
EKbox: slavecore3 load success!
[    0.018401] Detected VIPT I-cache on CPU1
[    0.018450] GICv3: CPU1: found redistributor 100 region 0:0x0000000024060000
[    0.018530] CPU1: Booted secondary processor 0x0000000100 [0x411fd050]
[    0.020256] Detected VIPT I-cache on CPU2
[    0.020294] GICv3: CPU2: found redistributor 200 region 0:0x0000000024080000
[    0.020360] CPU2: Booted secondary processor 0x0000000200 [0x411fd050]
[    0.021820] Detected VIPT I-cache on CPU3
[    0.021857] GICv3: CPU3: found redistributor 300 region 0:0x00000000240a0000
[    0.021918] CPU3: Booted secondary processor 0x0000000300 [0x411fd050]
[    0.022093] smp: Brought up 1 node, 4 CPUs
[    0.022153] SMP: Total of 4 processors activated.
[    0.022164] CPU features: detected: Privileged Access Never
[    0.022173] CPU features: detected: 32-bit EL0 Support
[    0.022182] CPU features: detected: Common not Private translations
[    0.022191] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.022201] CPU features: detected: CRC32 instructions
[    0.022209] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.022218] CPU features: detected: 32-bit EL1 Support
[    0.022228] CPU features: detected: RCpc load-acquire (LDAPR)
[    0.022946] CPU: All CPU(s) started at EL2
[    0.023015] alternatives: patching kernel code
[    0.024371] devtmpfs: initialized
[    0.028970] KASLR enabled
[    0.029822] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.029875] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.030087] kworker/u8:0 (32) used greatest stack depth: 12992 bytes left
[    0.030674] pinctrl core: initialized pinctrl subsystem
[    0.032979] DMI not present or invalid.
[    0.033069] softdog_kthread_create
[    0.033967] NET: Registered protocol family 16
[    0.035074] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.035172] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.035301] audit: initializing netlink subsys (disabled)
[    0.035529] audit cpu affinity init success
[    0.035632] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1
[    0.040003] thermal_sys: Registered thermal governor 'step_wise'
[    0.040713] cpuidle: using governor ladder
[    0.040775] cpuidle: using governor menu
[    0.040979] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.041164] ASID allocator initialised with 65536 entries
[    0.041893] Serial: AMBA PL011 UART driver
[    0.129239] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.129267] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.129278] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.129289] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.139017] ACPI: Interpreter disabled.
[    0.139159] iommu: Default domain type: Translated 
[    0.140802] NetLabel: Initializing
[    0.140832] NetLabel:  domain hash size = 128
[    0.140841] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.140941] NetLabel:  unlabeled traffic allowed by default
[    0.142819] clocksource: Switched to clocksource arch_sys_counter
[    0.184041] VFS: Disk quotas dquot_6.6.0
[    0.184153] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.185018] pnp: PnP ACPI: disabled
[    0.208610] NET: Registered protocol family 2
[    0.208873] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.210988] tcp_listen_portaddr_hash hash table entries: 1024 (order: 3, 40960 bytes, linear)
[    0.211053] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.211117] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.211282] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[    0.211510] TCP: Hash tables configured (established 16384 bind 16384)
[    0.211700] UDP hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.211816] UDP-Lite hash table entries: 1024 (order: 4, 98304 bytes, linear)
[    0.212163] NET: Registered protocol family 1
[    0.212216] PCI: CLS 0 bytes, default 64
[    0.212466] Trying to unpack rootfs image as initramfs...
[    0.440036] Freeing initrd memory: 5120K
[    0.440680] kvm [1]: KVM ncsnp disabled
[    0.440700] kvm [1]: KVM dvmbm disabled
[    0.440736] kvm [1]: IPA Size Limit: 40 bits
[    0.441772] kvm [1]: GICv3: no GICV resource entry
[    0.441787] kvm [1]: disabling GICv2 emulation
[    0.441821] kvm [1]: GIC system register CPU interface enabled
[    0.442066] kvm [1]: vgic interrupt IRQ16
[    0.442314] kvm [1]: Hyp mode initialized successfully
[    0.446561] modsign: There is no certification file
[    0.446590] modsign: There is only one cert or no cert
[    0.446600] Initialise system trusted keyrings
[    0.447119] workingset: timestamp_bits=43 max_order=19 bucket_order=0
[    0.460234] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.460678] Huawei Secure C library init
[    0.460701] cms cbb init
[    0.461046] modsign: create major 250 for module crl devs
[    0.503122] Key type asymmetric registered
[    0.503152] Asymmetric key parser 'x509' registered
[    0.503244] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.503546] io scheduler mq-deadline registered
[    0.626787] create /sys/kernel/tty_status_trace succ.
[    0.626853] did not found ttyname.
[    0.626864] default tty_suspend_mode is 0.
[    0.626875] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.627116] Serial: 8250/16550 suspend register ok.
[    0.627137] get_tty_suspend_info: mode is 0
[    0.630277] printk: console [ttyS0] disabled
[    0.630399] 8710000.uart: ttyS0 at MMIO 0x8710000 (irq = 23, base_baud = 6250000) is a 16550A
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd050]
[    0.000000] Linux version 5.10.0 (oe-user@oe-host) (aarch64-euler-linux-gcc (BiSheng Embedded CPU 303.1.0.B010) 7.3.0, GNU ld (BiSheng Embedded CPU 303.1.0.B010) 2.41) #1 SMP PREEMPT Mon Dec 15 15:23:35 CST 2025
[    0.000000] Machine model: Hisilicon Hi1711 ASIC
[    0.000000] efi: UEFI not found.
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] NUMA: NODE_DATA [mem 0xeffe6640-0xeffe7fff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000084be0000-0x0000000084bfefff]
[    0.000000]   node   0: [mem 0x0000000087200000-0x00000000efffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000084be0000-0x00000000efffffff]
[    0.000000] On node 0 totalpages: 429599
[    0.000000]   DMA zone: 6865 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 429599 pages, LIFO batch:63
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.5
[    0.000000] [dts]:cpu type is 1711
[    0.000000] can't find led ctrl node, please check it
[    0.000000] percpu: Embedded 30 pages/cpu s85224 r8192 d29464 u122880
[    0.000000] pcpu-alloc: s85224 r8192 d29464 u122880 alloc=30*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 422734
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: console=ttyS0,115200n8N earlycon=uart8250,mmio32,0x08710000 initrd=${initrd_load_addr},${initrd_size} rdinit=/sbin/init rw ekbox=0x20000$0x84be0000 kbox_mem=0x2e0000@0x84900000 swift_irqsoff_enable swxn=1
[    0.000000] Fallback order for Node 0: 0 
[    0.000000] printk: log_buf_len individual max cpu contribution: 4096 bytes
[    0.000000] printk: log_buf_len total cpu_extra contributions: 12288 bytes
[    0.000000] printk: log_buf_len min size: 16384 bytes
[    0.000000] printk: log_buf_len: 32768 bytes
[    0.000000] printk: early log buf free: 13912(84%)
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1666672K/1718396K available (7808K kernel code, 926K rwdata, 1516K rodata, 1856K init, 2377K bss, 51724K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] kmemleak: Kernel memory leak detector disabled
[    0.630955] printk: console [ttyS0] enabled
[    0.633007] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.650419] brd: module loaded
[    0.658643] loop: module loaded
[    0.660780] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.661390] fiq_glue_parse_source_common fiq source is 1!
[    0.661413] fiq_glue_parse_type_common fiq type is 0!
[    0.661424] fiq_glue_parse_buffer_offset_type fiq get cpu id type is default!
[    0.661437] fiq_glue_parse_clean_wdt fiq clean-wdt is 0!
[    0.661446] fiq_glue_parse_dead_loop fiq dead-loop is 1!
[    0.661456] fiq_glue_parse_invalid_cache fiq invalid-cache is 1!
[    0.661466] fiq_glue_parse_use_atf_under_same_image fiq use-atf-under-same-image is 0!
[    0.661477] fiq_glue_no_info_init fiq_num is 1, fiq_num_max is 16
[    0.661487] fiq_glue_no_info_init i 0 fiq-no 141
[    0.663246] KBOX: kbox:create region panic, size=65536

cat /proc/kbox/regions/panic
[20260402102343]usb device-0: gadget unbind 
[20260402102343]dwc3 8800000.dwc3: request ffff24cdf28f8000 was not queued to ep1in
[20260402102343]dwc3 8800000.dwc3: request ffff24cdf28f8a80 was not queued to ep2in
[20260402102343]usb device-0: command connect. function count 2 
[20260402102344]usb device-0: attach driver 
[20260402102344]usb device-0: gadget bind 
[20260402102344]usb device-0: Bind speed 2.0 
[20260402102344]usb device-0: gadget suspend 
[20260402102345]usb device-0: command disconnect 
[20260402102345]usb device-0: detach driver
[20260402102345]usb device-0: gadget disconnect 
[20260402102345]usb device-0: reset configuration. gadget state <8> 
[20260402102345]usb device-0: gadget unbind 
[20260402102345]dwc3 8800000.dwc3: request ffff24cdf28f8300 was not queued to ep1in
[20260402102345]dwc3 8800000.dwc3: request ffff24cdf28f8600 was not queued to ep2in
[20260402102345]usb device-0: command connect. function count 2 
[20260402102346]usb device-0: attach driver 
[20260402102346]usb device-0: gadget bind 
[20260402102346]usb device-0: Bind speed 2.0 
[20260402102346]usb device-0: gadget suspend 
[20260402102346]usb device-0: command disconnect 
[20260402102346]usb device-0: detach driver
[20260402102346]usb device-0: gadget disconnect 
[20260402102346]usb device-0: reset configuration. gadget state <8> 
[20260402102346]usb device-0: gadget unbind 
[20260402102346]dwc3 8800000.dwc3: request ffff24ce0deaecc0 was not queued to ep1in
[20260402102346]dwc3 8800000.dwc3: request ffff24ce0deae300 was not queued to ep2in
[20260402102347]usb device-0: command connect. function count 2 
[20260402102347]usb device-0: attach driver 
[20260402102347]usb device-0: gadget bind 
[20260402102347]usb device-0: Bind speed 2.0 
[20260402102347]usb device-0: gadget suspend 
[20260402102355]usb device-0: gadget reset 
[20260402102355]usb device-0: reset configuration. gadget state <8> 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x08 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x08 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x02 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x04 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260402102355]usb device-0: setup configuration. gadget state <6> 
[20260402102355]usb device-0: Keyboard configured 
[20260402102355]usb device-0: Mouse configured 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x08 0x00 0x00 0x00 0x00 0x01 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0xa1 0x03 0x00 0x00 0x01 0x00 0x01 0x00 
[20260402102355]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x01 0x00 0x00 0x00 
[20260402102758]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260402102758]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403013109]72,2026-04-03 01:31:09,2752,mctp_reset,1477,reset mctp ok!
[20260403013109]73,2026-04-03 01:31:09,2752,mctp_dereset,1501,dereset mctp ok!
[20260403013327]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403013404]74,2026-04-03 01:34:04,47043,hisfc_drv_probe,834,probe bus 0
[20260403013404]75,2026-04-03 01:34:04,47043,hisfc_drv_request_permission,628,sfc0 use hwid 4
[20260403013404]76,2026-04-03 01:34:04,47043,hisfc_flash_scan_init,1050,hisfc_probe start bus 0
[20260403013404]77,2026-04-03 01:34:04,47043,sfc_sys_set_controller_clk,246,bus 0 clock frequency of is all set!
[20260403013404]78,2026-04-03 01:34:04,47043,sfc_sys_clock_operator,213,CLOSE 1711 SFC Clock Success!
[20260403013404]79,2026-04-03 01:34:04,47043,sfc_sys_clock_operator,223,Open 1711 SFC Clock Success!
[20260403013404]80,2026-04-03 01:34:04,47043,sfc_core_spi_probe,2053,Spi(cs0) ID: 0x00000000 0x00000000
[20260403013404]81,2026-04-03 01:34:04,47043,sfc_core_spi_probe,2056,Spi(cs0): RDID not right!
[20260403013404]82,2026-04-03 01:34:04,47043,sfc_core_spi_probe,2053,Spi(cs1) ID: 0xc22539c2 0x2539c225
[20260403013404]83,2026-04-03 01:34:04,47043,sfc_spi_search_rw,125,dump[3] isread(1) iftype:1
[20260403013404]84,2026-04-03 01:34:04,47043,sfc_spi_search_rw,125,dump[1] isread(0) iftype:1
[20260403013404]85,2026-04-03 01:34:04,47043,sfc_core_show_spi,1690,Spi(cs 1): 
[20260403013404]86,2026-04-03 01:34:04,47043,sfc_core_show_spi,1691,Name:"MX25U25645G"
[20260403013404]Creating 1 MTD partitions on "hi_sfc0.1":
[20260403013404]0x000000000000-0x000002000000 : "sfc0cs1"
[20260403013405]87,2026-04-03 01:34:05,47056,hisfc_drv_remove,888,hisfc_drv_remove
[20260403013405]88,2026-04-03 01:34:05,47056,hisfc_drv_remove,896,hisfc_drv_remove bus 0
[20260403013405]Deleting MTD partitions on "hi_sfc0.1":
[20260403013405]Deleting sfc0cs1 MTD partition
[20260403013439]89,2026-04-03 01:34:39,2750,mctp_reset,1477,reset mctp ok!
[20260403013439]90,2026-04-03 01:34:39,2750,mctp_dereset,1501,dereset mctp ok!
[20260403013514]usb device-0: gadget reset 
[20260403013514]usb device-0: reset configuration. gadget state <7> 
[20260403013514]usb device-0: Keyboard disabled 
[20260403013514]usb device-0: Mouse disabled 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x08 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x08 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x02 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x04 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260403013514]usb device-0: setup configuration. gadget state <6> 
[20260403013514]usb device-0: Keyboard configured 
[20260403013514]usb device-0: Mouse configured 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x08 0x00 0x00 0x00 0x00 0x01 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0xa1 0x03 0x00 0x00 0x01 0x00 0x01 0x00 
[20260403013514]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x01 0x00 0x00 0x00 
[20260403013615]usb device-0: gadget reset 
[20260403013615]usb device-0: reset configuration. gadget state <7> 
[20260403013615]usb device-0: Keyboard disabled 
[20260403013615]usb device-0: Mouse disabled 
[20260403013616]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x40 0x00 
[20260403013616]usb device-0: gadget reset 
[20260403013616]usb device-0: reset configuration. gadget state <5> 
[20260403013616]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260403013616]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x09 0x00 
[20260403013616]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403013616]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0xff 0x00 
[20260403013616]usb device-0: setup-request[T:8][0]:0x80 0x06 0x01 0x03 0x09 0x04 0xff 0x00 
[20260403013616]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260403013616]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260403013616]usb device-0: setup configuration. gadget state <6> 
[20260403013616]usb device-0: Keyboard configured 
[20260403013616]usb device-0: Mouse configured 
[20260403013617]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260403013617]usb device-0: setup-request[T:8][0]:0x21 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 
[20260403013617]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x00 0x00 0x3f 0x00 
[20260403013617]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403013617]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260403013617]usb device-0: setup-request[T:8][0]:0x21 0x0a 0x00 0x00 0x01 0x00 0x00 0x00 
[20260403013617]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260403013624]edma: 1851, host is registered.
[20260403015201]91,2026-04-03 01:52:01,47133,gmac_link_handle,412,eth2 link down! speed(0x6) duplex(0x0).
[20260403015206]92,2026-04-03 01:52:06,47133,gmac_link_handle,409,eth2 link up! speed(0x8) duplex(0x1).
[20260403015207]93,2026-04-03 01:52:07,47133,gmac_link_handle,412,eth2 link down! speed(0x6) duplex(0x0).
[20260403015209]94,2026-04-03 01:52:09,47133,gmac_link_handle,409,eth2 link up! speed(0x8) duplex(0x1).
[20260403015330]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403015359]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403040059]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403040100]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403040349]95,2026-04-03 04:03:49,2747,mctp_reset,1477,reset mctp ok!
[20260403040349]96,2026-04-03 04:03:49,2747,mctp_dereset,1501,dereset mctp ok!
[20260403040356]edma: 1862, host is lost.
[20260403040404]97,2026-04-03 04:04:04,2751,mctp_reset,1477,reset mctp ok!
[20260403040404]98,2026-04-03 04:04:04,2751,mctp_dereset,1501,dereset mctp ok!
[20260403040426]usb device-0: gadget reset 
[20260403040426]usb device-0: reset configuration. gadget state <7> 
[20260403040426]usb device-0: Keyboard disabled 
[20260403040426]usb device-0: Mouse disabled 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x08 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x08 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x02 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x04 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260403040426]usb device-0: setup configuration. gadget state <6> 
[20260403040426]usb device-0: Keyboard configured 
[20260403040426]usb device-0: Mouse configured 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x08 0x00 0x00 0x00 0x00 0x01 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0xa1 0x03 0x00 0x00 0x01 0x00 0x01 0x00 
[20260403040426]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x01 0x00 0x00 0x00 
[20260403040448]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403040449]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403085056]99,2026-04-03 08:50:56,2751,mctp_reset,1477,reset mctp ok!
[20260403085056]100,2026-04-03 08:50:56,2751,mctp_dereset,1501,dereset mctp ok!
[20260403090639]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090639]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090642]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090646]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090646]101,2026-04-03 09:06:46,51517,hisfc_drv_probe,834,probe bus 0
[20260403090646]102,2026-04-03 09:06:46,51517,hisfc_drv_request_permission,628,sfc0 use hwid 4
[20260403090646]103,2026-04-03 09:06:46,51517,hisfc_flash_scan_init,1050,hisfc_probe start bus 0
[20260403090646]104,2026-04-03 09:06:46,51517,sfc_sys_set_controller_clk,246,bus 0 clock frequency of is all set!
[20260403090646]105,2026-04-03 09:06:46,51517,sfc_sys_clock_operator,213,CLOSE 1711 SFC Clock Success!
[20260403090646]106,2026-04-03 09:06:46,51517,sfc_sys_clock_operator,223,Open 1711 SFC Clock Success!
[20260403090646]107,2026-04-03 09:06:46,51517,sfc_core_spi_probe,2053,Spi(cs0) ID: 0x00000000 0x00000000
[20260403090646]108,2026-04-03 09:06:46,51517,sfc_core_spi_probe,2056,Spi(cs0): RDID not right!
[20260403090646]109,2026-04-03 09:06:46,51517,sfc_core_spi_probe,2053,Spi(cs1) ID: 0xc22539c2 0x2539c225
[20260403090646]110,2026-04-03 09:06:46,51517,sfc_spi_search_rw,125,dump[3] isread(1) iftype:1
[20260403090647]111,2026-04-03 09:06:46,51517,sfc_spi_search_rw,125,dump[1] isread(0) iftype:1
[20260403090647]112,2026-04-03 09:06:47,51517,sfc_core_show_spi,1690,Spi(cs 1): 
[20260403090647]113,2026-04-03 09:06:47,51517,sfc_core_show_spi,1691,Name:"MX25U25645G"
[20260403090647]Creating 1 MTD partitions on "hi_sfc0.1":
[20260403090647]0x000000000000-0x000002000000 : "sfc0cs1"
[20260403090647]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090647]114,2026-04-03 09:06:47,51530,hisfc_drv_remove,888,hisfc_drv_remove
[20260403090647]115,2026-04-03 09:06:47,51530,hisfc_drv_remove,896,hisfc_drv_remove bus 0
[20260403090647]Deleting MTD partitions on "hi_sfc0.1":
[20260403090647]Deleting sfc0cs1 MTD partition
[20260403090650]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090723]116,2026-04-03 09:07:23,2749,mctp_reset,1477,reset mctp ok!
[20260403090723]117,2026-04-03 09:07:23,2749,mctp_dereset,1501,dereset mctp ok!
[20260403090725]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090725]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090732]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090748]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090755]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090756]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403090757]usb device-0: gadget reset 
[20260403090757]usb device-0: reset configuration. gadget state <7> 
[20260403090757]usb device-0: Keyboard disabled 
[20260403090757]usb device-0: Mouse disabled 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x08 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x08 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x02 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x04 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260403090757]usb device-0: setup configuration. gadget state <6> 
[20260403090757]usb device-0: Keyboard configured 
[20260403090757]usb device-0: Mouse configured 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x08 0x00 0x00 0x00 0x00 0x01 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0xa1 0x03 0x00 0x00 0x01 0x00 0x01 0x00 
[20260403090757]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x01 0x00 0x00 0x00 
[20260403090829]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403090830]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091527]118,2026-04-03 09:15:27,2749,mctp_reset,1477,reset mctp ok!
[20260403091527]119,2026-04-03 09:15:27,2749,mctp_dereset,1501,dereset mctp ok!
[20260403091608]120,2026-04-03 09:16:08,2750,mctp_reset,1477,reset mctp ok!
[20260403091608]121,2026-04-03 09:16:08,2750,mctp_dereset,1501,dereset mctp ok!
[20260403091642]usb device-0: gadget reset 
[20260403091642]usb device-0: reset configuration. gadget state <7> 
[20260403091642]usb device-0: Keyboard disabled 
[20260403091642]usb device-0: Mouse disabled 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x08 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x08 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x02 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x04 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260403091643]usb device-0: setup configuration. gadget state <6> 
[20260403091643]usb device-0: Keyboard configured 
[20260403091643]usb device-0: Mouse configured 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x08 0x00 0x00 0x00 0x00 0x01 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0xa1 0x03 0x00 0x00 0x01 0x00 0x01 0x00 
[20260403091643]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x01 0x00 0x00 0x00 
[20260403091716]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091716]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091720]dwc3 8800000.dwc3: failed to send remote wakeup
[20260403091721]usb device-0: gadget reset 
[20260403091721]usb device-0: reset configuration. gadget state <7> 
[20260403091721]usb device-0: Keyboard disabled 
[20260403091721]usb device-0: Mouse disabled 
[20260403091721]usb device-0: command disconnect 
[20260403091721]usb device-0: detach driver
[20260403091721]usb device-0: gadget disconnect 
[20260403091721]usb device-0: reset configuration. gadget state <5> 
[20260403091721]usb device-0: gadget unbind 
[20260403091721]dwc3 8800000.dwc3: request ffff24ce01e78000 was not queued to ep1in
[20260403091721]dwc3 8800000.dwc3: request ffff24ce01e78d80 was not queued to ep2in
[20260403091721]usb device-0: command connect. function count 2 
[20260403091722]usb device-0: attach driver 
[20260403091722]usb device-0: gadget bind 
[20260403091722]usb device-0: Bind speed 2.0 
[20260403091722]usb device-0: gadget suspend 
[20260403091722]usb device-0: gadget reset 
[20260403091722]usb device-0: reset configuration. gadget state <8> 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x08 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x09 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0xff 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x01 0x03 0x09 0x04 0xff 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260403091722]usb device-0: setup configuration. gadget state <6> 
[20260403091722]usb device-0: Keyboard configured 
[20260403091722]usb device-0: Mouse configured 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x21 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x00 0x00 0x3f 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x21 0x0a 0x00 0x00 0x01 0x00 0x00 0x00 
[20260403091722]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260403091728]edma: 1851, host is registered.
[20260403091832]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091854]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091855]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091949]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403091950]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260403092715]122,2026-04-03 09:27:15,2747,mctp_reset,1477,reset mctp ok!
[20260403092715]123,2026-04-03 09:27:15,2747,mctp_dereset,1501,dereset mctp ok!
[20260403092750]124,2026-04-03 09:27:50,2752,mctp_reset,1477,reset mctp ok!
[20260403092750]125,2026-04-03 09:27:50,2752,mctp_dereset,1501,dereset mctp ok!
[20260403092812]126,2026-04-03 09:28:12,2752,mctp_reset,1477,reset mctp ok!
[20260403092812]127,2026-04-03 09:28:12,2752,mctp_dereset,1501,dereset mctp ok!
[20260403092831]128,2026-04-03 09:28:31,2750,mctp_reset,1477,reset mctp ok!
[20260403092831]129,2026-04-03 09:28:31,2750,mctp_dereset,1501,dereset mctp ok!
[20260403092847]130,2026-04-03 09:28:47,2751,mctp_reset,1477,reset mctp ok!
[20260403092847]131,2026-04-03 09:28:47,2751,mctp_dereset,1501,dereset mctp ok!
[20260403092858]edma: 1862, host is lost.
[20260407084318]132,2026-04-07 08:43:18,5569,gmac_link_handle,412,eth2 link down! speed(0x6) duplex(0x0).
[20260407084324]133,2026-04-07 08:43:24,5569,gmac_link_handle,409,eth2 link up! speed(0x7) duplex(0x1).
[20260407084634]EXT4-fs (mmcblk0gp2): mounted filesystem 29059e08-1f74-4f55-ae8b-11aed26d36ba ro with ordered data mode. Opts: (null)
[20260407084634]EXT4-fs (mmcblk0gp2): unmounting filesystem 29059e08-1f74-4f55-ae8b-11aed26d36ba.
[20260407084655]134,2026-04-07 08:46:55,2902,gpio_cmd_get_int_event,1321,gpio_get_int_event errs(-4)
[20260407084656]skynet (3253) used greatest stack depth: 10528 bytes left
[20260407084656]skynet (3327) used greatest stack depth: 9552 bytes left
[20260407084656]135,2026-04-07 08:46:56,2872,ipmb_cmd_check_data_readable,1285,ipmb check read was interrupted, ret = -4
[20260407084656]136,2026-04-07 08:46:56,3116,btc_recv_data,234,btc(0) recv req msg ERESTARTSYS, btc_state(0).
[20260407084656]137,2026-04-07 08:46:56,3117,btc_recv_data,234,btc(1) recv req msg ERESTARTSYS, btc_state(0).
[20260407084657]usb device-0: detach driver
[20260407084657]usb device-0: gadget disconnect 
[20260407084657]usb device-0: reset configuration. gadget state <7> 
[20260407084657]usb device-0: Keyboard disabled 
[20260407084657]usb device-0: Mouse disabled 
[20260407084657]usb device-0: gadget unbind 
[20260407084657]dwc3 8800000.dwc3: request ffff24ce01e78180 was not queued to ep1in
[20260407084657]dwc3 8800000.dwc3: request ffff24ce01e78c00 was not queued to ep2in
[20260407084700]hisport_cdev: 1342, listen thread end, ret=0
[20260407084700]EXT4-fs (mmcblk0gp3): unmounting filesystem 2b36f01e-1ff8-4124-a4a3-eb5b3196d16f.
[20260407084700]EXT4-fs (loop0): unmounting filesystem 7e3d1636-b845-4936-9517-c79e3d772080.
[20260407084701]EXT4-fs (mmcblk0p7): unmounting filesystem e885af12-99c2-47f1-907b-7669489b9ff9.
[20260407084702]systemd-shutdown[1]: Syncing filesystems and block devices.
[20260407084702]systemd-shutdown[1]: Sending SIGTERM to remaining processes...
[20260407084702]systemd-journald[1272]: Received SIGTERM from PID 1 (systemd-shutdow).
[20260407084702]systemd-shutdown[1]: Sending SIGKILL to remaining processes...
[20260407084702]systemd-shutdown[1]: Unmounting file systems.
[20260407084702](sd-remount)[10236]: Remounting '/var/log' read-only in with options '(null)'.
[20260407084702]EXT4-fs (mmcblk0p9): re-mounted 286f8d12-6b40-45fc-b368-892d70ee4e21 ro. Opts: (null)
[20260407084702](sd-umount)[10237]: Unmounting '/var/log'.
[20260407084702]EXT4-fs (mmcblk0p9): unmounting filesystem 286f8d12-6b40-45fc-b368-892d70ee4e21.
[20260407084702](sd-umount)[10237]: Unmounted '/var/log'.
[20260407084702](sd-remount)[10238]: Remounting '/data' read-only in with options '(null)'.
[20260407084702](sd-remount)[10238]: Failed to remount '/data' read-only: Device or resource busy
[20260407084702](sd-umount)[10239]: Unmounting '/data'.
[20260407084702](sd-umount)[10239]: Failed to unmount /data: Device or resource busy
[20260407084702](sd-umount)[10240]: Unmounting '/var'.
[20260407084702](sd-umount)[10240]: Unmounted '/var'.
[20260407084702](sd-remount)[10241]: Remounting '/data' read-only in with options '(null)'.
[20260407084702](sd-remount)[10241]: Failed to remount '/data' read-only: Device or resource busy
[20260407084702](sd-umount)[10242]: Unmounting '/data'.
[20260407084702](sd-umount)[10242]: Failed to unmount /data: Device or resource busy
[20260407084702]systemd-shutdown[1]: Not all file systems unmounted, 1 left.
[20260407084702]systemd-shutdown[1]: Deactivating swaps.
[20260407084702]systemd-shutdown[1]: All swaps deactivated.
[20260407084702]systemd-shutdown[1]: Detaching loop devices.
[20260407084702]systemd-shutdown[1]: Detaching loopback /dev/loop0.
[20260407084702]systemd-shutdown[1]: All loop devices detached.
[20260407084702]systemd-shutdown[1]: Stopping MD devices.
[20260407084702]systemd-shutdown[1]: All MD devices stopped.
[20260407084702]systemd-shutdown[1]: Detaching DM devices.
[20260407084702]systemd-shutdown[1]: Detaching DM /dev/dm-0 (253:0).
[20260407084702]device-mapper: ioctl: systemd-shutdow[1]: dm-0 (mmcblksp) is removed successfully
[20260407084702]systemd-shutdown[1]: All DM devices detached.
[20260407084702]systemd-shutdown[1]: Unmounting file systems.
[20260407084702](sd-remount)[10247]: Remounting '/data' read-only in with options '(null)'.
[20260407084703]EXT4-fs (mmcblk0p1): re-mounted f138e627-b0bc-4dd9-8404-afe01465ddfb ro. Opts: (null)
[20260407084703](sd-umount)[10248]: Unmounting '/data'.
[20260407084703]EXT4-fs (mmcblk0p1): unmounting filesystem f138e627-b0bc-4dd9-8404-afe01465ddfb.
[20260407084703](sd-umount)[10248]: Unmounted '/data'.
[20260407084703]systemd-shutdown[1]: All filesystems unmounted.
[20260407084703]systemd-shutdown[1]: All filesystems, swaps, loop devices, MD devices and DM devices detached.
[20260407084703]systemd-shutdown[1]: Syncing filesystems and block devices.
[20260407084703]systemd-shutdown[1]: Rebooting.
[20260407084703]kvm: exiting hardware virtualization
[20260407084703]Kernel Offset: 0x29e7c1c00000
[20260407084703]Module Offset: 0x29e79ddef000
[20260407084703]Linear Region Offset: 0x24cdc0000000
[20260407084703]xhci-hcd xhci-hcd.1.auto: Host halt failed, -110
[20260407084703]xhci-hcd xhci-hcd.0.auto: Host halt failed, -110
[20260407084705]reboot: Restarting system
[20260407084705]KBOX: [machine_restart:238]
------------------kbox restart:[    0.663356]----------------
KBOX: load OK
tasklock: sched_ctrl created.
registered taskstats version 1
Loading compiled-in X.509 certificates
page_owner is disabled
RTOS Process Context for RPC init success
ima: Allocated hash algorithm: sha256
ima: No architecture policies found
DIM: No measurement list to restore, it's ok
clk: Disabling unused clocks
dw-apb-uart 8710000.uart: forbid DMA for kernel console
Freeing unused kernel memory: 1856K
**** Total Boot time: 733 ms, uncompress initrd cost 227 ms ****
Run /init as init process
  with arguments:
    /init
    swift_irqsoff_enable
  with environment:
    HOME=/
    TERM=linux
    earlycon=uart8250,mmio32,0x08710000
    rdinit=/sbin/init
    kbox_mem=0x2e0000@0x84900000
load_kallsyms: loading out-of-tree module taints kernel.
rtos_kallsyms: Successfully loaded symbols!
modprobe (1123) used greatest stack depth: 12752 bytes left
hisi_request_fiq num is 1
[RTOS fiq]@@ register fiq
[RTOS fiq] FIQ register mem:(____ptrval____), FIQ dfx addr: (____ptrval____)[RTOS fiq] FIQ reserved memory for reigsters: (____ptrval____)
[RTOS fiq]smc register: a0:83000004, a1:(____ptrval____), a2:(____ptrval____)
[request_fiq] succeed to register fiq-no 141  first func hook_for_fiq+0x0/0x2c [rtos_snapshot]
hisi_request_fiq success to request the 0 fiq 141
1,1970-01-01 00:00:00,1134,bdinfo_boot_cfg_init,2648,board_type:0x0, platform_id:0x0, board_id:0xff, pcb_ver:0x2.
2,1970-01-01 00:00:00,1134,bdinfo_boot_cfg_init,2651,ddr_size:0x3, ddr_bits:0x1, ddr_ecc:0x1.
3,1970-01-01 00:00:00,1134,bdinfo_boot_cfg_init,2655,single_chip:0x0, debug_gmac:0x1, vga_type:0x0, is_espi:0x0.
4,1970-01-01 00:00:00,1134,comm_probe,935,comm_probe success!
insmod (1134) used greatest stack depth: 12368 bytes left
insmod (1140) used greatest stack depth: 12320 bytes left
5,1970-01-01 00:00:00,1151,watchdog_probe,837,watchdog init ok!
insmod (1151) used greatest stack depth: 12288 bytes left
6,1970-01-01 00:00:00,1163,emmc_vendor_hook_init,42,emmc hook init, register ret:0.
7,1970-01-01 00:00:01,49,emmc_close_cache,32,close emmc cache.
mmc0: new HS200 MMC card at address 0001
mmcblk0: mmc0:0001 Y2P032 27.9 GiB 
mmcblk0boot0: mmc0:0001 Y2P032 partition 1 4.00 MiB
mmcblk0boot1: mmc0:0001 Y2P032 partition 2 4.00 MiB
mmcblk0gp0: mmc0:0001 Y2P032 partition 4 384 MiB
mmcblk0gp1: mmc0:0001 Y2P032 partition 5 384 MiB
mmcblk0gp2: mmc0:0001 Y2P032 partition 6 384 MiB
mmcblk0gp3: mmc0:0001 Y2P032 partition 7 128 MiB
 mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 >
random: date: uninitialized urandom read (8 bytes read)
random: date: uninitialized urandom read (8 bytes read)
random: date: uninitialized urandom read (8 bytes read)
EXT4-fs (mmcblk0gp2): mounted filesystem 29059e08-1f74-4f55-ae8b-11aed26d36ba ro with ordered data mode. Opts: (null)
mount (1232) used greatest stack depth: 12144 bytes left
systemd[1]: Inserted module 'autofs4'
NET: Registered protocol family 10
Segment Routing with IPv6
systemd[1]: systemd 249 running in system mode (+PAM -AUDIT +SELINUX -APPARMOR +IMA +SMACK -SECCOMP -GCRYPT -GNUTLS -OPENSSL +ACL +BLKID -CURL -ELFUTILS -FIDO2 -IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP +LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -BZIP2 -LZ4 +XZ -ZLIB -ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=legacy)
systemd[1]: Detected architecture arm64.
systemd[1]: No hostname configured, using default hostname.
systemd[1]: Hostname set to <localhost>.
systemd[1]: Initializing machine ID from random generator.
systemd[1]: Installed transient /etc/machine-id file.
systemd-fstab-g (1249) used greatest stack depth: 11888 bytes left
systemd-sysv-generator[1257]: SysV service '/etc/init.d/syslog' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd-sysv-generator[1257]: SysV service '/etc/init.d/auditd' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd-sysv-generator[1257]: SysV service '/etc/init.d/busybox-cron' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd-sysv-generator[1257]: SysV service '/etc/init.d/busybox-udhcpd' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd-sysv-generator[1257]: SysV service '/etc/init.d/network' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd-sysv-generator[1257]: SysV service '/etc/init.d/functions' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd-sysv-generator[1257]: SysV service '/etc/init.d/crond' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd-sysv-generator[1257]: SysV service '/etc/init.d/mdev' lacks a native systemd unit file. Automatically generating a unit file for compatibility. Please update package to include a native systemd unit file, in order to make it more safe and robust.
systemd[1]: /lib/systemd/system/dbus.socket:5: ListenStream= references a path below legacy directory /var/run/, updating /var/run/dbus/system_bus_socket → /run/dbus/system_bus_socket; please update the unit file accordingly.
systemd[1]: multi-user.target: Wants dependency dropin /etc/systemd/system/multi-user.target.wants/lsw.service is not a symlink, ignoring.
systemd[1]: /etc/systemd/system/interface.service:11: Unknown key name 'PermittedCapabilities' in section 'Service', ignoring.
systemd[1]: /etc/systemd/system/interface.service:12: Unknown key name 'InheritableCapabilities' in section 'Service', ignoring.
systemd[1]: /etc/systemd/system/interface.service:13: Unknown key name 'EffectiveCapabilities' in section 'Service', ignoring.
systemd[1]: Configuration file /lib/systemd/system/file_transfer.service is marked world-inaccessible. This has no effect as configuration data is accessible via APIs without restrictions. Proceeding anyway.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Queued start job for default target Multi-User System.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Created slice Slice /system/getty.
random: systemd: uninitialized urandom read (16 bytes read)
systemd[1]: Created slice Slice /system/modprobe.
systemd[1]: Created slice User and Session Slice.
systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
systemd[1]: Started Forward Password Requests to Wall Directory Watch.
systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
systemd[1]: Reached target Path Units.
systemd[1]: Reached target Slice Units.
systemd[1]: Reached target Swaps.
systemd[1]: Listening on initctl Compatibility Named Pipe.
systemd[1]: Listening on Journal Socket (/dev/log).
systemd[1]: Listening on Journal Socket.
systemd[1]: Mounting Kernel Debug File System...
systemd[1]: Mounting Kernel Trace File System...
systemd[1]: Starting Create List of Static Device Nodes...
systemd[1]: Starting Load Kernel Module configfs...
systemd[1]: Starting Load Kernel Module drm...
systemd[1]: Starting Load Kernel Module fuse...
systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
systemd[1]: systemd-journald.service: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
systemd[1]: Starting Journal Service...
systemd[1]: Condition check resulted in Load Kernel Modules being skipped.
systemd[1]: Starting Remount Root and Kernel File Systems...
systemd[1]: Starting Apply Kernel Variables...
systemd[1]: Started Journal Service.
random: systemd: uninitialized urandom read (16 bytes read)
random: systemd-journal: uninitialized urandom read (16 bytes read)
random: systemd-tmpfile: uninitialized urandom read (8 bytes read)
systemd-journald[1273]: Received client request to flush runtime journal.
random: systemd: uninitialized urandom read (16 bytes read)
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
usbcore: registered new interface driver usb-storage
random: crng init done
random: 1339 urandom warning(s) missed due to ratelimiting
8,1970-01-01 00:00:07,1380,gmac_phy_init,1101,mac(0) not used phy.
9,1970-01-01 00:00:08,1380,gmac_phy_init,1101,mac(1) not used phy.
10,1970-01-01 00:00:09,1380,gmac_phy_init,1099,mac(2)'s phy_addr is 3.
11,1970-01-01 00:00:10,1380,gmac_phy_init,1101,mac(3) not used phy.
12,1970-01-01 00:00:11,1380,gmac_hw_set_port_mode_all,635,SGMII auto-negotiation not complete(0x0)
13,1970-01-01 00:00:11,1380,gmac_probe,1433,gmac init ok!
14,1970-01-01 00:00:11,1397,sys_info_probe,1960,sys_info init ok!
15,1970-01-01 00:00:11,1413,p80_probe,210,p80 use LPC!
16,1970-01-01 00:00:11,1419,sol_probe,906,SOL use LPC!
17,1970-01-01 00:00:11,1419,sol_ddrinfo_update,814,SOL[0] Init Rx-start 0x86000000, Rx-size 0x3, Tx-start 0x86200000, Tx-size 0x3.
18,1970-01-01 00:00:11,1419,sol_ddrinfo_update,814,SOL[1] Init Rx-start 0x86400000, Rx-size 0x1, Tx-start 0x86480000, Tx-size 0x4.
19,1970-01-01 00:00:11,1419,sol_ddrinfo_update,814,SOL[2] Init Rx-start 0x86880000, Rx-size 0x3, Tx-start 0x86a80000, Tx-size 0x1.
20,1970-01-01 00:00:11,1419,sol_ddrinfo_update,814,SOL[3] Init Rx-start 0x86b00000, Rx-size 0x3, Tx-start 0x86d00000, Tx-size 0x2.
21,1970-01-01 00:00:11,1419,sol_probe,935,uart sol init ok!
22,1970-01-01 00:00:11,1425,dboot_probe,545,dboot probe start.
23,1970-01-01 00:00:11,1425,dboot_probe_info,519,boot from uboot 0
24,1970-01-01 00:00:11,1425,dboot_probe_info,520,BMC reset count: 0
25,1970-01-01 00:00:11,1425,dboot_probe_info,521,BMC unsec reset count: 4
26,1970-01-01 00:00:11,1425,dboot_probe_info,522,HOST reset count: 2
27,1970-01-01 00:00:11,1425,dboot_probe_info,523,CHIP reset count: 0
28,1970-01-01 00:00:11,1425,dboot_probe,567,dboot init ok!
29,1970-01-01 00:00:11,1441,bmcrtc_of_probe,189,BMCRTC Device Registered.
8711000.uart: ttySS3 at MMIO 0x8711000 (irq = 24, base_baud = 0) is a AMBA/ttySS
8743000.uart: ttySS4 at MMIO 0x8743000 (irq = 25, base_baud = 0) is a AMBA/ttySS
8744000.uart: ttySS5 at MMIO 0x8744000 (irq = 26, base_baud = 0) is a AMBA/ttySS
875d000.uart: ttySS6 at MMIO 0x875d000 (irq = 27, base_baud = 0) is a AMBA/ttySS
875e000.uart: ttySS7 at MMIO 0x875e000 (irq = 28, base_baud = 0) is a AMBA/ttySS
30,1970-01-01 00:00:11,1473,peci_probe,332,peci is 1 mode!
31,1970-01-01 00:00:11,1473,peci_probe,346,peci init ok!
32,1970-01-01 00:00:12,1491,hispi_setup_device,885,hispi_setup_device id 0x0!
33,1970-01-01 00:00:12,1491,hispi_setup_device,885,hispi_setup_device id 0x1!
34,1970-01-01 00:00:12,1518,pci_fix_ker_probe,527,probe OK
35,1970-01-01 00:00:12,1522,deal_with_ext_addr,255,g_mctp_ext_mode:0 [0 Normal,1 Offset,2 Hi]
36,1970-01-01 00:00:12,1522,mctp_reset,1477,reset mctp ok!
37,1970-01-01 00:00:12,1522,mctp_dereset,1501,dereset mctp ok!
insmod (1528) used greatest stack depth: 11632 bytes left
38,1970-01-01 00:00:12,1564,vce_dac_param_set,244,dac param register is: 0x800820f
39,1970-01-01 00:00:12,1564,vce_driver_probe,295,irq_mask 0xd80
[request_fiq] succeed to register fiq-no 141 more func dfx_dying_saying+0x0/0x20 [dfx_drv]
40,1970-01-01 00:00:12,38,gmac_link_handle,409,eth2 link up! speed(0x7) duplex(0x1).
EXT4-fs (mmcblk0p7): mounted filesystem e885af12-99c2-47f1-907b-7669489b9ff9 r/w with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p1): mounted filesystem f138e627-b0bc-4dd9-8404-afe01465ddfb r/w with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p7): unmounting filesystem e885af12-99c2-47f1-907b-7669489b9ff9.
EXT4-fs (mmcblk0p9): mounted filesystem 286f8d12-6b40-45fc-b368-892d70ee4e21 r/w with ordered data mode. Opts: (null)
EXT4-fs (mmcblk0p7): mounted filesystem e885af12-99c2-47f1-907b-7669489b9ff9 r/w with ordered data mode. Opts: (null)
systemd-journald[1273]: Received client request to flush runtime journal.
EXT4-fs (mmcblk0gp3): mounted filesystem 2b36f01e-1ff8-4124-a4a3-eb5b3196d16f r/w with ordered data mode. Opts: (null)
[pmfs]: pramdisk: registered block device major 254
[pmfs]: starting add gendisk!
[pmfs]: add gendisk done!
[pmfs]: pramdisk: module loaded
loop0: detected capacity change from 0 to 209715200
EXT4-fs (loop0): mounted filesystem 7e3d1636-b845-4936-9517-c79e3d772080 r/w with ordered data mode. Opts: (null)
hisport_cdev: 1322, ioremap:0x40000000
edma: 2298, ==========1711 device==========
edma: 815, CHECK SUM MATCH ,RETURN 
FS-Cache: Loaded
CacheFiles: Loaded
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
FS-Cache: Netfs 'nfs' registered for caching
FS-Cache: Netfs 'cifs' registered for caching
Key type cifs.idmap registered
device-mapper: ioctl: 4.43.0-ioctl (2020-10-01) initialised: dm-devel@redhat.com
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010
xhci-hcd xhci-hcd.0.auto: irq 125, io mem 0x08a00000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010
xhci-hcd xhci-hcd.1.auto: irq 127, io mem 0x0cc00000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
insmod (2209) used greatest stack depth: 10752 bytes left
cryptd: max_cpu_qlen set to 1000
edma: 1851, host is registered.
memory_monitor. (2279): drop_caches: 4
edma: 1862, host is lost.
[I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
EXT4-fs (mmcblk0gp1): mounted filesystem c690570a-2e27-41c2-b035-3c943e0e1e98 ro without journal. Opts: noload
EXT4-fs (mmcblk0gp1): unmounting filesystem c690570a-2e27-41c2-b035-3c943e0e1e98.
ext2 filesystem being remounted at /dev/shm/chroot/2723/opt/bmc/pram supports timestamps until 2038-01-19 (0x7fffffff)
41,2026-04-07 08:48:38,2686,msg_sec_module_cmd_cpy_to_user,523,msg copy_to_user user data error 8
42,2026-04-07 08:48:38,2686,msg_scm3_ioctl,613,msg cmd(0xc0047301) handle error!
43,2026-04-07 08:48:39,2690,hw_get_hard_lock,79,hw_lock(0x2) is locked by M3
44,2026-04-07 08:48:39,2690,hw_acquire_hard_lock,141,hardware lock(2) is't locked by A55(-1)
45,2026-04-07 08:48:39,1237,hw_get_hard_lock,79,hw_lock(0x2) is locked by M3
46,2026-04-07 08:48:39,1237,hw_acquire_hard_lock,141,hardware lock(2) is't locked by A55(-1)
47,2026-04-07 08:48:39,1259,hw_get_hard_lock,79,hw_lock(0x2) is locked by M3
48,2026-04-07 08:48:39,1259,hw_acquire_hard_lock,141,hardware lock(2) is't locked by A55(-1)
49,2026-04-07 08:48:43,1237,hw_get_hard_lock,79,hw_lock(0x2) is locked by M3
50,2026-04-07 08:48:43,1237,hw_acquire_hard_lock,141,hardware lock(2) is't locked by A55(-1)
[I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
FAT-fs (mmcblk0p5): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
device-mapper: ioctl: dmsetup[2940]: dm-0 (mmcblksp) is created successfully
device-mapper: ioctl: dmsetup[2947]: dm-0 (mmcblksp) is removed successfully
device-mapper: ioctl: dmsetup[2971]: dm-0 (mmcblksp) is created successfully
IPv6: ADDRCONF(NETDEV_CHANGE): veth: link becomes ready
51,2026-04-07 08:48:52,3006,init_btc_mode,434,btc mode(2)
53,2026-04-07 08:48:52,3006,btc_lb_int_pin_init,439,pin(63) is reused as gpio
53,2026-04-07 08:48:52,ISR,sysctrl_rst_int_handle,436,Receive subsys_rst_irq(41), int_reg(0x13c) int_sts(0x417b)!
####dump test 0####
btc dev mode:2
btc priv:0 0
btc priv param:61 63
####dump test 1####
btc dev mode:2
btc priv:1 0
btc priv param:61 63
54,2026-04-07 08:48:52,3006,btc_probe,555,btc init ok!
[20260407084855]55,2026-04-07 08:48:55,2925,mctp_reset,1477,reset mctp ok!
[20260407084855]56,2026-04-07 08:48:55,2925,mctp_dereset,1501,dereset mctp ok!
[20260407084909]usbcore: registered new interface driver cdc_ether
[20260407084912]usbcore: registered new interface driver rndis_host
[20260407084914][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407084915][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407084915][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407084918]usb device-0: command connect. function count 2 
[20260407084918]usb device-0: attach driver 
[20260407084918]usb device-0: gadget bind 
[20260407084918]usb device-0: Bind speed 2.0 
[20260407084918]usb device-0: gadget suspend 
[20260407084920][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x510|0x0>
[20260407084942][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084942][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084943][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084943][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084945][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084945][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084945][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084946][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084948][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084948][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084948][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084949][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084950][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084951][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084951][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084952][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084953][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084954][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084954][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084956][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084956][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084957][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084957][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084959][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084959][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407084959][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085000][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085002][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085002][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085002][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085002][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085004][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085004][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085005][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085005][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085007][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085007][I2C-03-RT<-11|-11>] M<0x5d|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085008][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085008][I2C-01-RT<-5|-5>] M<0x30|0x1|0x0|1|10> L<1|195|0> C<1|182|13> E<0xa00|0x0|0x0|0x0> I<0x0|0x514|0x0>
[20260407085008][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|3|0> C<1|0|3> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085011][I2C-03-RT<-11|-11>] M<0x5c|0x1|0x0|1|10> L<1|2|0> C<1|0|2> E<0x801|0x0|0x0|0x1000> I<0x0|0x510|0x0>
[20260407085020][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085120][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085220][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085320][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085336]57,2026-04-07 08:53:36,5760,hisfc_drv_probe,834,probe bus 0
[20260407085336]58,2026-04-07 08:53:36,5760,hisfc_drv_request_permission,628,sfc0 use hwid 4
[20260407085336]59,2026-04-07 08:53:36,5760,hisfc_flash_scan_init,1050,hisfc_probe start bus 0
[20260407085336]60,2026-04-07 08:53:36,5760,sfc_sys_set_controller_clk,246,bus 0 clock frequency of is all set!
[20260407085336]61,2026-04-07 08:53:36,5760,sfc_sys_clock_operator,213,CLOSE 1711 SFC Clock Success!
[20260407085336]62,2026-04-07 08:53:36,5760,sfc_sys_clock_operator,223,Open 1711 SFC Clock Success!
[20260407085336]63,2026-04-07 08:53:36,5760,sfc_core_spi_probe,2053,Spi(cs0) ID: 0x00000000 0x00000000
[20260407085336]64,2026-04-07 08:53:36,5760,sfc_core_spi_probe,2056,Spi(cs0): RDID not right!
[20260407085336]65,2026-04-07 08:53:36,5760,sfc_core_spi_probe,2053,Spi(cs1) ID: 0xc22539c2 0x2539c225
[20260407085336]66,2026-04-07 08:53:36,5760,sfc_spi_search_rw,125,dump[3] isread(1) iftype:1
[20260407085336]67,2026-04-07 08:53:36,5760,sfc_spi_search_rw,125,dump[1] isread(0) iftype:1
[20260407085336]68,2026-04-07 08:53:36,5760,sfc_core_show_spi,1690,Spi(cs 1): 
[20260407085336]69,2026-04-07 08:53:36,5760,sfc_core_show_spi,1691,Name:"MX25U25645G"
[20260407085336]Creating 1 MTD partitions on "hi_sfc0.1":
[20260407085336]0x000000000000-0x000002000000 : "sfc0cs1"
[20260407085337]70,2026-04-07 08:53:37,5773,hisfc_drv_remove,888,hisfc_drv_remove
[20260407085337]71,2026-04-07 08:53:37,5773,hisfc_drv_remove,896,hisfc_drv_remove bus 0
[20260407085337]Deleting MTD partitions on "hi_sfc0.1":
[20260407085337]Deleting sfc0cs1 MTD partition
[20260407085410]72,2026-04-07 08:54:10,2879,mctp_reset,1477,reset mctp ok!
[20260407085410]73,2026-04-07 08:54:10,2879,mctp_dereset,1501,dereset mctp ok!
[20260407085420][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x08 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x08 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x02 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0x04 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260407085446]usb device-0: setup configuration. gadget state <6> 
[20260407085446]usb device-0: Keyboard configured 
[20260407085446]usb device-0: Mouse configured 
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x08 0x00 0x00 0x00 0x00 0x01 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x00 0x00 0x00 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0xa1 0x03 0x00 0x00 0x01 0x00 0x01 0x00 
[20260407085446]usb device-0: setup-request[T:8][0]:0x21 0x0b 0x00 0x00 0x01 0x00 0x00 0x00 
[20260407085521][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085530]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260407085530]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260407085555]usb device-0: gadget reset 
[20260407085555]usb device-0: reset configuration. gadget state <7> 
[20260407085555]usb device-0: Keyboard disabled 
[20260407085555]usb device-0: Mouse disabled 
[20260407085556]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x40 0x00 
[20260407085556]usb device-0: gadget reset 
[20260407085556]usb device-0: reset configuration. gadget state <5> 
[20260407085556]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x01 0x00 0x00 0x12 0x00 
[20260407085556]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x09 0x00 
[20260407085556]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x02 0x00 0x00 0x3b 0x00 
[20260407085556]usb device-0: setup-request[T:8][0]:0x80 0x06 0x00 0x03 0x00 0x00 0xff 0x00 
[20260407085556]usb device-0: setup-request[T:8][0]:0x80 0x06 0x01 0x03 0x09 0x04 0xff 0x00 
[20260407085556]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260407085556]usb device-0: setup-request[T:8][0]:0x00 0x09 0x01 0x00 0x00 0x00 0x00 0x00 
[20260407085556]usb device-0: setup configuration. gadget state <6> 
[20260407085556]usb device-0: Keyboard configured 
[20260407085556]usb device-0: Mouse configured 
[20260407085557]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260407085557]usb device-0: setup-request[T:8][0]:0x21 0x0a 0x00 0x00 0x00 0x00 0x00 0x00 
[20260407085557]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x00 0x00 0x3f 0x00 
[20260407085557]usb device-0: setup-request[T:8][0]:0x21 0x09 0x00 0x02 0x00 0x00 0x01 0x00 
[20260407085557]usb device-0: setup-request[T:8][0]:0x80 0x06 0x02 0x03 0x09 0x04 0xff 0x00 
[20260407085557]usb device-0: setup-request[T:8][0]:0x21 0x0a 0x00 0x00 0x01 0x00 0x00 0x00 
[20260407085557]usb device-0: setup-request[T:8][0]:0x81 0x06 0x00 0x22 0x01 0x00 0x3c 0x00 
[20260407085610]edma: 1851, host is registered.
[20260407085621][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085721][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x510|0x0>
[20260407085733]nginx (3203) used greatest stack depth: 9360 bytes left
[20260407085821][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407085921][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>
[20260407090021][I2C-08-RT<-5|-5>] M<0x21|0x1|0x0|1|10> L<1|1|0> C<1|0|1> E<0x801|0x0|0x0|0x1> I<0x0|0x710|0x0>

cat /proc/kbox/regions/dying
cat /proc/kbox/regions/ks_0

cat /proc/kbox/regions/ks_1

cat /proc/kbox/regions/ks_2

cat /proc/kbox/regions/ks_3

cat /proc/kbox/regions/ks_main

